FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 6 of 22 FirstFirst ... 4 5 6 7 8 16 ... LastLast
Results 51 to 60 of 220

Thread: Backlit Electronic Instrument Cluster

  1. #51
    DMCTalk.org's #2 Mike C.'s Avatar
    Join Date:  May 2011

    Location:  Huntersville, NC

    Posts:    1,402

    My VIN:    16336 (SOLD)

    That's awesome Jim! Keep it up!
    One of DMCTalk.org's original admins

    Mainly lurking, just passing through. Still enjoying reading about everyone's progress.

  2. #52
    Let's see if you bastards can do 90. dvonk's Avatar
    Join Date:  May 2011

    Location:  Omaha, NE

    Posts:    1,755

    My VIN:    loading, please wait...

    +1, im excited about this and i dont even have a D yet...
    Obtain-O-Meter: 128%
    as of 2016/08/04
    0%|====|====|====|====|====50%====|====|====|====|====|100%

  3. #53
    Member
    Join Date:  Oct 2011

    Location:  Orange County, California

    Posts:    40

    My VIN:    5086

    I have experience and a good source for rapid prototyping if you're considering using any sort of additive manufacturing for a prototype or mold.

  4. #54
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Thread bump!

    Any progress?
    3.0L, automatic, carbureted

  5. #55
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Yes, still progressing. No new good details to report yet. But certainly still progressing.

    On a side note, if anyone can figure out a way to obtain ONE or TWO of these chips...

    http://mcrmotorusa.com/IC%20Drivers.html

    Or compatible Switec M-S Quad Driver X12.017

    It would be a spectacular help. They should be the *key* to a good fluid needle. However the only manufacturer/distributor I've found of them or equivalents will only sell by the case. A box of 100 at $6.50 each. I dont want to buy the whole damn case until I know for sure I can get the electronics to work right. They've told me their "dealer" network only sells their stepper motors.

    So there's a little preview of the costs which will be involved in development of this. That box of 100 costing $650 will supply *ONE* component needed twice in each dash, enough for 50 dash units. Fortunately not many other components will have such a high minimum purchase requirement.
    Jim Reeve
    DMC6960

  6. #56
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Quote Originally Posted by dmc6960 View Post
    On a side note, if anyone can figure out a way to obtain ONE or TWO of these chips...

    http://mcrmotorusa.com/IC%20Drivers.html

    Or compatible Switec M-S Quad Driver X12.017
    Also compatible is a VID66-06 or VID66-08 chip. These are all manufactured in China and seem to only sell in even larger quantities than I can get the other one for. They are all cross-compatible.

    ***BOUNTY***

    If anyone can find me a small quantity (or individual) of these for a reasonable price, I will reward you with $20 or a more substantial discount on the finished product.
    Jim Reeve
    DMC6960

  7. #57
    Member sphiend's Avatar
    Join Date:  May 2011

    Location:  Atlanta

    Posts:    98

    There seems to be a bunch of stepper motor ic's on eBay available in small quantities. I know nothing about this stuff but thought perhaps you could have a look there.

    Search eBay for stepper motor ic
    -=-=-=-=-=-=-=-=-
    Sphiend - VIN 6510
    -=-=-=-=-=-=-=-=-

  8. #58
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    I have easy access to the actual stepper motors. They are sold by everyone to replace the original bad ones on mid-2000's GM vehicles.

    What I'm looking for is a source for new IC driver chips which effortlessly drive the stepper motors in a smooth fluid motion. I've found several compatible chips, but no source to buy a small quantity of them for prototyping.

    http://mcrmotorusa.com/IC%20Drivers.html
    MS Quad Driver X12.017
    VID66-06
    VID66-08
    Jim Reeve
    DMC6960

  9. #59
    Senior Member ramblinmike's Avatar
    Join Date:  May 2011

    Location:  Alton, IL

    Posts:    302

    My VIN:    00910

    mouser.com seems to have a bunch of driver chips available individually.
    Yeah, it's dirty. I drive it.

  10. #60
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Small Update...

    Dedicated "specific" driver chips are assumed to be not available right now, based on my refusal to buy a very large quantity without knowing if I can get them to work right.

    On that note, I have progressed with programming a chip to drive the stepper motor directly. Its a crude program, one for forwards and one for reverse, nothing linking the two or varying how fast it moves and nothing to stop it (except the stepper's physical stop).

    BUT IT WORKS.

    As I have time on Sunday and Monday to further refine the program, I'll take a video and post it up.
    Jim Reeve
    DMC6960

Page 6 of 22 FirstFirst ... 4 5 6 7 8 16 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •