FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 65 of 111 FirstFirst ... 15 55 63 64 65 66 67 75 ... LastLast
Results 641 to 650 of 1102

Thread: Farrar's car blog

  1. #641
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by Ron View Post
    If the holes are too big, can't you just get different anchors?
    (I'm not familiar with what you are doing.)
    In some cases, the material where the stud was mounted has been split. Have you ever seen a sausage that has burst its casing? It's kind of like that. There's some material at the edge of the kneepad for the stud to sit in, but apart from that the kneepad is hollow (to accommodate the HVAC duct) and the material will not stick to anything. This is why making a new kneepad might actually be less trouble than repairing the original.

    Farrar
    3.0L, automatic, carbureted

  2. #642
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,636

    My VIN:    03572

    Quote Originally Posted by Ron View Post
    If the holes are too big, can't you just get different anchors?
    (I'm not familiar with what you are doing.)
    The plastic splits (on my car). I used epoxy and glued the original bolt back in with the crack clamped shut. So far it is holding fine.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  3. #643
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by Bitsyncmaster View Post
    The plastic splits (on my car). I used epoxy and glued the original bolt back in with the crack clamped shut. So far it is holding fine.
    Dave, you are more skilled than I am. I couldn't figure out a way to clamp shut the cracks in the corners of my kneepads.

    One thing I have thought about: making a single-piece kneepad for the driver's side. Since I am the only person who drives my car and I have the steering column adjusted all the way to the top, I think it would look nice to have a single kneepad that goes all the way across with a U-shape cut out to cradle the steering column, like Proto-1's interior has.

    Farrar
    3.0L, automatic, carbureted

  4. #644
    My friends think I'm nuts jawn101's Avatar
    Join Date:  May 2011

    Location:  Sacramento-ish

    Posts:    4,408

    My VIN:    02100

    Club(s):   (NCDMC) (DCUK)

    A great way to clamp corners is with a ratcheting tie-down strap. Not sure if that will address your specific situation but thought I would mention it Just wrap the strap around the circumference of the part and ratchet down gently.

    Edit: if you mean just the round stud where the bolt is mounted, the same principle applies - just use a cable tie instead and cut it off when you're done.
    Last edited by jawn101; 01-18-2012 at 12:17 PM.
    Jon
    1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
    restoration log, March 2011 to present
    full and detailed photo restoration log

  5. #645
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Thanks, Jon.

    The inside is where the material is split. In theory I guess I could remove the vinyl, drill two holes one on either side of the corner of the kneepad, and then push the zip-tie through the holes. But that is too much work for me, I think.

    I will have to see about making new kneepads. I have some more ideas percolating, but will have to put them on the back burner until after Feb. 3 when I am finished with all of my Carnival season work. In the meantime, the evaporator has to come out, so I might as well remove the kneepads and set them aside for the time being.

    Farrar
    3.0L, automatic, carbureted

  6. #646
    My friends think I'm nuts jawn101's Avatar
    Join Date:  May 2011

    Location:  Sacramento-ish

    Posts:    4,408

    My VIN:    02100

    Club(s):   (NCDMC) (DCUK)

    Ah, crap. Oh well, worth a shot. What were you thinking of making the replacements out of? I saw you mention the hard craft store foam - if you mean the green crap it is just that... Lol. It will flake everywhere and if your girlfriend puts her feet on the kneepads, they will crush and deform permanently

    Might be a cool exercise to have some sheet metal bent into the right shape and put some padding on, then the vinyl. I don't know if that would be prohibitively expensive, especially with the need to weld in studs. Good luck!
    Jon
    1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
    restoration log, March 2011 to present
    full and detailed photo restoration log

  7. #647
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    If the green foam they make ottomans out of really is that bad, then I will probably order some high-density polyurethane foam from McMaster-Carr.

    Farrar
    3.0L, automatic, carbureted

  8. #648
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,636

    My VIN:    03572

    Quote Originally Posted by Farrar View Post
    Dave, you are more skilled than I am. I couldn't figure out a way to clamp shut the cracks in the corners of my kneepads.

    One thing I have thought about: making a single-piece kneepad for the driver's side. Since I am the only person who drives my car and I have the steering column adjusted all the way to the top, I think it would look nice to have a single kneepad that goes all the way across with a U-shape cut out to cradle the steering column, like Proto-1's interior has.

    Farrar
    One of those wood working clamps with two jaws made from maple and has two closing screws with handles. Those clamps work wonders doing weird stuff like that.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  9. #649
    My friends think I'm nuts jawn101's Avatar
    Join Date:  May 2011

    Location:  Sacramento-ish

    Posts:    4,408

    My VIN:    02100

    Club(s):   (NCDMC) (DCUK)

    Quote Originally Posted by Farrar View Post
    If the green foam they make ottomans out of really is that bad, then I will probably order some high-density polyurethane foam from McMaster-Carr.

    Farrar
    Ohh. I was thinking of that hard foam for flowers and such. I used it to carve a form for something years ago and it was such an awful material. Hard and brittle and flaky. Upholstery foam would probably be fine, maybe even too soft to hold a form reliably?
    Jon
    1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
    restoration log, March 2011 to present
    full and detailed photo restoration log

  10. #650
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    18.Jan.2012
    Quote Originally Posted by jawn101 View Post
    Ohh. I was thinking of that hard foam for flowers and such. I used it to carve a form for something years ago and it was such an awful material. Hard and brittle and flaky. Upholstery foam would probably be fine, maybe even too soft to hold a form reliably?
    Oh, no -- now I know what you're talking about and you're correct. The stuff I am talking about is a lighter shade of green and is the same type of foam they use in seat cushions, except firmer. All told, it would probably be a little softer than the stock polyurethane knee pads, but it holds its shape very well. I have some scrap pieces of vinyl I could use for testing purposes to see how the material would stand up to constant bumping and deforming over a period of time.

    Alternately, I could order some maximum-rigidity polyurethane foam online. This would be comparable to the compressability of the stock knee pads, only slightly less firm. Two 18"x6" cylinders (which I would then cut to shape) would cost me around $12 each. Only problem is if it doesn't work I can't send it back for a refund and then I am stuck with a bunch of foam and nothing to do with it.

    Farrar

    I have too many irons in the fire right now -- my latest order from SuperBrightLEDs arrived today, so the kneepads can wait!

    Farrar

    Problem with my glorious enormous trunk lights: they're too heavy.

    Although I was able to get the light bars to stick to the Velcro with weatherstrip adhesive, the weight of the light bars was starting to dislodge the carpet. So I have elected to go a different route. This will involve some soldering, but I may be able to get to it tomorrow and get pictures of it if it doesn't rain. It should still throw a lot of light nonetheless.

    23.Jan.2012

    Last night's attempt at installing the new trunk lighting was successful but for the fact that I dropped, and then could not locate again, one of the connectors I was planning on using -- and it was the last one! Unfortunately, it was too late for me to go to the auto parts store because it would have been dark by the time I got back. However, I did manage to fasten the new LED units to the trunk with black weatherstrip adhesive and confirm (by touching the bare wire to the other connector) that the light thrown will be enough to illuminate the area properly, and -- most important -- shed way more light than the stock fixture while using less current than the old incandescent bulb.

    ***

    26.Jan.2012

    OK, time for a little audience participation:

    Since I will be driving #2613 to Orlando next year, I have the following things to take care of:

    1. air conditioning
    2. cruise control
    3. reducing the amount of road noise

    Are those in the right order, or do you think I should do road noise reduction before cruise control? Either way, it involves taking the interior out of the car.

    GO!

    Also, I am 33 today if anyone was wondering. Cookies will be welcome.
    3.0L, automatic, carbureted

Page 65 of 111 FirstFirst ... 15 55 63 64 65 66 67 75 ... LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •