Location: Sacramento-ish
Posts: 4,408
My VIN: 02100
Club(s): (NCDMC) (DCUK)
Jon
1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
restoration log, March 2011 to present
full and detailed photo restoration log
Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
Thanks to Steve Rice, Sparky is back on the ground now. His floor jack is superior to mine in two ways: it is shorter, and it raises higher. I was unaware that there was such a thing as a "low profile jack" until now -- so I am going to buy one since I am tired of crawling under the car and lifting it with my shoulder to get the jack underneath. The Duralast jack that I bought will live in the PT Cruiser in case I ever need to change a tire.
I have confirmed that the drip I found is gear oil from the final drive, leaking out around the passenger-side output flange. Looks like the Grady seals I got were either installed incorrectly or not up to the task. (And yes, we also installed the O-rings and sleeves when we did the job a year or so ago.) Those seals felt good to me so I doubt they were NOS but rather newly manufactured. Nonetheless, I have heard good things about John Hervey's double-lip seals. Since I am going to buy one of his rebuilt axles anyway, I might as well add those to the list.
3.0L, automatic, carbureted
Location: Dahlonega GA
Posts: 2,462
Club(s): (SEDOC) (DCUK)
eBay selling at it's best I can tell you stock Delorians and quite a bit of slugs so the Turbo is a super nice up-grade.
K-Jet: Causing electrical issues since November 5th 1955
Location: Sacramento-ish
Posts: 4,408
My VIN: 02100
Club(s): (NCDMC) (DCUK)
I *have* John's double-lip seals but have not installed them yet. They look to be really top quality stuff. I actually have them for the output shafts as well as the front and rear main engine seals. I did install the front (crank pulley) seal and it seated nicely and fixed that leak instantly. No felt to wear out.
Jon
1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
restoration log, March 2011 to present
full and detailed photo restoration log
Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
Strangely, the O'Reilly Auto Parts store website says that they have the output shaft seals in stock, but only for the automatic transmission. Since I remember quite clearly what the seals look like, I may go and have a look at what they have. I can't believe they would be correct, so if nothing else I can report to them that they need to change the listing on their website.
3.0L, automatic, carbureted
Location: Taylors SC
Posts: 5,327
My VIN: (former)05429
Club(s): (DMWC) (DCUK)
That would be interesting, because the seals are the same for manual/auto.
Dave S
DMC Midwest - retired but helping
Greenville SC
Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
I had to go somewhere else instead, so I will check O'Reilly tomorrow. In the meantime, my vacuum hose has come in. I got 1/8" thick blue silicone hose from McMaster to redo all of my vacuum lines -- and I mean ALL of them, including the ones inside the car. The firm silicone grips very well, and I have had a problem with some of the old hose letting go. I also plan on replacing the hard plastic line that goes through the car with a contiguous silicone run. Although black hose is available, I got blue to make it different from all of the other black hoses in my engine compartment. (I would like to eventually get another color for the coolant hoses -- preferably green. But that's a long way off.) The only drawback with the blue McMaster hose is that it's translucent, which means that eventually parts of it will look ugly with oily residue inside. But now that I think of it, translucent air hose would also be diagnostically useful -- easy to see if I have a block or kink somewhere, or if the engine is sucking oil badly. Anyway, it doesn't matter since I am the only one who will ever look at it.
Tomorrow will be a big day -- I plan on taking out the driver's seat to fix the stud, and replacing the vacuum hoses and intake manifold O-rings. Then if I am lucky I can fire up the engine and see if I have a vacuum leak.
3.0L, automatic, carbureted
Location: Rochester, NY
Posts: 2,405
My VIN: 01049
-Mike
My engine twists my frame.
1981 DeLorean, Carb LS4 swap completed
1999 Corvette, cam/headers/intake manifold, 400 rwhp
2005 Elise, stock
2016 Chevy Cruze