FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 14 of 22 FirstFirst ... 4 12 13 14 15 16 ... LastLast
Results 131 to 140 of 220

Thread: Backlit Electronic Instrument Cluster

  1. #131
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    All Numbers Done

    Finished the 4. All numeral characters for the cluster are complete. They are all based off of the speedometer and tachometer numbers. All secondary numbers (kph and small gauges) use identical typeface just scaled smaller.

    Quick summary...

    All characters are 3mm wide by 5.6mm tall. Exceptions are the 1, which is 1.6mm wide, and the 4, which is 3.5mm wide. Majority of the line widths are approximately .8mm with several exceptions. The radii used on the 0 does NOT completely match the other character's radii, but is close. The vertical portion of the 0 is perfectly strait with no radii, and all other characters have a very slight radii in most of their vertical portions. Characters with dual loops (3,5,6,8 ) have a larger radii on the bottom loop than the top loop. The 5 and 6 have a much larger bottom radii than the bottom of the 3 and 8. The 9 does not exist on any OEM design, 85mph, 140mph, or metric.

    I will now work on drawing out all the letters. MPH, km/h, RPM/100, VOLTS, TEMP, OIL, FUEL.

    If anyone has high resolution pictures or vector graphics of the common automotive icons for Battery, Temp, Oil, and Fuel; it would be very helpful. I'm not looking forward to drawing those especially since they exist identically everywhere. There must be a good source for them.

    The final lineup....

    0.jpg 1.jpg 2.jpg 3.jpg 4.jpg 5.jpg 6.jpg 7.jpg 8.jpg 9-2.jpg
    Jim Reeve
    DMC6960

  2. #132
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Gimmie an M...P...H!!!

    M.jpg P.jpg H.jpg

    And then some...
    speedo1.jpg
    After struggling with the P, then realizing it matches some skewed angles of the 0, nearly everything I need for the speedometer is done. As you can see I've also started on the actual speedo itself. Only have the easy bits right now though, as I've previously measured these dimensions they were easy to draw. Perhaps slightly more difficult will be all the angled hash-marks on their exact angle and position, but I don't foresee too much difficulty. Of course there is no "outline" on the speedo face right now, and as the colors are inverted its hard to tell exactly where the borders are. You could highlight the image though if you need a basic idea. When I get it completed I'll have all the colors proper so it'll look exactly like a DeLorean speedometer.
    Jim Reeve
    DMC6960

  3. #133
    Senior Member
    Join Date:  Sep 2011

    Location:  LaFayette, Ga/Chattanooga, Tn

    Posts:    126

    My VIN:    6410

    Something that I was thinking about working on is an LCD replacement to go where the clock and rheostat are located. Its purpose would be like on a modern car display information such as door status, Avg. MPG, Inst. MPG, Check Engine, Cruise Control Output, Outside Temp, Maybe Compass, etc... I love your progress and cant wait to see your prototype at DCS! I havent fully decided about my project yet, although It would be a good addition to your cluster. In my opinion anyway lol. What's everyones thoughts on the LCD?

    Davidrucker11387
    DeLoDave, 6410

  4. #134
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by davidrucker11387 View Post
    What's everyones thoughts on the LCD?
    My thought it is will have to have a hell of a good backlight to be seen in daylight. Sounds neat, though.
    3.0L, automatic, carbureted

  5. #135
    Aussie Member
    Join Date:  Feb 2012

    Location:  Adelaide

    Posts:    944

    My VIN:    6679

    Quote Originally Posted by Farrar View Post
    My thought it is will have to have a hell of a good backlight to be seen in daylight. Sounds neat, though.
    Or perhaps an OLED panel?

  6. #136
    Senior Member
    Join Date:  Sep 2011

    Location:  LaFayette, Ga/Chattanooga, Tn

    Posts:    126

    My VIN:    6410

    OLEDs are nice but sometimes hard to come by in the size format that I would like. Also if going the trouble of OLED I would want full color instead of 1 or 2 color formats like they are commonly available. The '84 Chrysler Laser is where my inspiration has come from so far on the LCD screen idea and I too was thinking on going with a digital dash but more on the lines of its obvious that its digital and not looks stock but works digitally also like the laser. I attached a picture for those of you that havent seen those cars.
    Attached Images

  7. #137
    Senior Member DMC5180's Avatar
    Join Date:  May 2011

    Location:  Reedsburg, WI

    Posts:    4,042

    My VIN:    5180

    Club(s):   (DMWC) (DCUK)

    If you want that kind of digital dash, it's sort of already been done using gauges from Dakota Digital.
    DENNIS

    VIN 5180, Frame 3652, STAGE II​, EPS​, DM-eng Solid State Solutions (RPM Rly, Dm.Lt.Mod., Fan Fail Mod. , FAN Rly, HS.Rly) , HID headlights, SPAX user since 2009, Eibach springs, M Adj. Rear LCA's, DPNW poly-sway bar kit, DMCEU LCA Stabilizer link kit, DMCMW Illuminated door sills, Aussie Illuminated SS Shifter plate, REAL MOMO EVO Steering wheel, DELOREANA Extended View Side Mirrors w/ Heaters, DELOREANA LED Door Lights.

  8. #138
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    I give you... A Speedometer.

    speedoprev.jpg

    First render of a speedometer. Few nuances still remaining...

    Most of the angles between ticks on the stock speedo are about 16º. However there are a few that are 15º and 14º. This variability will be too difficult to manage with my basic software for the needle. Therefore I have decided to make them all 16º. This results in the 5mph tick being a little too close to the trip rest opening. Unfortunately that opening is a fixed location, as the new shaft will need to be in the exact same spot to clear the cluster lens.

    The stock speedo is biased about 2º counter clockwise. I have recreated that here, but I may keep it strait on the final product. This will allow for better 5mph placement and better overall aesthetics.

    As is obiously noticeable, the km/h ticks are not here yet, perhaps tomorrow. I still need to draw a lowercase k, m, and h. With time running out I may omit that on the initial prototype prints.

    The prototype I hope to bring to DCS will be an 85mph speedometer. But the final product will still be available as 140mph or all metric (240kph).

    I will soon also be placing an order for a temp sender and oil pressure sender so I can use them as a measurement base without sacrificing my own car. I will be back to PIC programming soon now.
    Jim Reeve
    DMC6960

  9. #139
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Also just today I ordered a mid 80's Saab 900 fuel level sender. As I understand it this is a direct fit for our tank but with different connectors and perhaps no low fuel light switch. Also I believe this sender reverses the variable resistance from what the stock gauge needs to read (reverse full and empty). As I understand this is the fuel sender which TankZilla used. The new cluster will be able to operate on both this unit and stock style units, user selectable so you can change it out whenever you need to.
    Jim Reeve
    DMC6960

  10. #140
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Generic Fuel Level Sender

    Got the Saab fuel level sender today. This unit will fit inside the stock location for the OEM level sender. It reads in reverse of the OEM unit, so it is not a drop-in replacement for those without a good unit right now. I got this for two reasons, first is to have a benchtop unit for testing with the new cluster. And second is to eventually replace my original sender (still working mostly fine after 120k+ miles!). Since the new cluster will operate strictly off of logic, it is a relatively simple manner to create two programs which will operate in normal or reverse. User selectable! So the fuel gauge will work on original senders, and all DMCH reproduction senders, including the new all-in-one unit with the new fuel pump.

    sender.jpg

    In addition to that, I've been reading quite a few reports lately about people having problems with their TankZilla units. It also seems that most all of the problems are with the adapter box associated with it, NOT the unit itself, which I do believe is the exact unit I just purchased. Therefore people with TankZillas will be able to bypass their adapter boxes if they wish and run their sender directly with this new cluster.
    Jim Reeve
    DMC6960

Page 14 of 22 FirstFirst ... 4 12 13 14 15 16 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •