FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 85 of 111 FirstFirst ... 35 75 83 84 85 86 87 95 ... LastLast
Results 841 to 850 of 1102

Thread: Farrar's car blog

  1. #841
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    OK, so I am sorry I haven't been able to keep anyone updated on my progress here, but this week is fundraising week where I work, plus I had a math test and a paper due. Next week is Spring Break and my girlfriend will be out of town for six days, so let's hope that I can get some work done!
    3.0L, automatic, carbureted

  2. #842
    Aussie Member
    Join Date:  Feb 2012

    Location:  Adelaide

    Posts:    944

    My VIN:    6679

    Quote Originally Posted by Farrar View Post
    OK, so I am sorry I haven't been able to keep anyone updated on my progress here, but this week is fundraising week where I work, plus I had a math test and a paper due. Next week is Spring Break and my girlfriend will be out of town for six days, so let's hope that I can get some work done!
    I might take this quiet opportunity then to voice up and let you know I am one of the lurkers that have been following every post in your thread for more than half a year now and enjoy sharing your journey - cheers

  3. #843
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Thanks, Chris! Is it cool weather down there yet? I was sweating buckets today after just a few minutes inside the car and wishing that I had a/c in it.

    One step at a time, though, right? Here's a quick video to show where I am at the moment.

    http://youtu.be/t24Owr9cCV4
    3.0L, automatic, carbureted

  4. #844
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by Farrar View Post
    Thanks, Chris! Is it cool weather down there yet? I was sweating buckets today after just a few minutes inside the car and wishing that I had a/c in it.

    One step at a time, though, right? Here's a quick video to show where I am at the moment.

    http://youtu.be/t24Owr9cCV4
    Oh my. Now I want to take my car apart.

  5. #845
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by stevedmc View Post
    Oh my. Now I want to take my car apart.
    You will end up scratching your head a lot.

    The plastic piece above the battery that the electrical bracket is attached to seems to be simply glued on each side. It's very flexible. As for how the bracket is fastened to the plastic, I have no clue. There are no holes for screws under there, and besides if you used a screw to hold the bracket on, the screw would poke down into the battery compartment.

    My friend Lewis and I made an appropriate wood panel in a matter of minutes with his saber saw. I am currently cutting the necessary bevels around the wood piece with my Dremel tool's router bit, and about to glue on the top piece, then drill holes in it. I might paint it black before putting it in, but I'm not sure I will considering the amount of time that would add to the project.
    3.0L, automatic, carbureted

  6. #846
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,636

    My VIN:    03572

    Quote Originally Posted by Farrar View Post
    You will end up scratching your head a lot.

    The plastic piece above the battery that the electrical bracket is attached to seems to be simply glued on each side. It's very flexible. As for how the bracket is fastened to the plastic, I have no clue. There are no holes for screws under there, and besides if you used a screw to hold the bracket on, the screw would poke down into the battery compartment.

    My friend Lewis and I made an appropriate wood panel in a matter of minutes with his saber saw. I am currently cutting the necessary bevels around the wood piece with my Dremel tool's router bit, and about to glue on the top piece, then drill holes in it. I might paint it black before putting it in, but I'm not sure I will considering the amount of time that would add to the project.
    The relay bracket has one screw in the back and I think should have one or two on the right side. My right side screw had to be ground off so I installed one new screw more in the middle of the bracket down into the battery compartment with a nut inside the battery compartment.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  7. #847
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by Bitsyncmaster View Post
    The relay bracket has one screw in the back and I think should have one or two on the right side. My right side screw had to be ground off so I installed one new screw more in the middle of the bracket down into the battery compartment with a nut inside the battery compartment.
    Dave, I am glad to see someone has done this, because I was thinking of the same thing... good to know that you can get a nut and the end of a screw in there without interfering with battery placement.

    In other news, I beveled the edges of the wood panel where necessary using my Dremel tool's router bit at the lowest speed. With that done, I applied Liquid Nails to adhere the small piece to the top rear of the panel -- I was tempted to just use wood screws, but since I had it I figured I might as well use it. I may put screws in just for peace of mind, though.

    With the wood pieces set aside for the adhesive to dry, I am getting other work done: currently I am making templates for my custom console build. Here is where I am so far as I take a break for dinner.

    SANY0124.jpg

    I used ordinary posterboard for the templates for a couple of reasons: first, it is cheap and plentiful; second, I can cut it with ordinary scissors; third, I can fold it and rip it to shape while it is in the car; fourth, I can tape sheets of it together to make adjustments without the result being too thick to move around in the car. Of course, it was so humid outside today that it started wilting almost immediately after I took it out of the apartment, but that is not a problem so much as a surprise.

    I realized that the plastic I bought from McMaster in late 2010 (when I first thought about doing the console and nothing else more important had cropped up) is too small. For the long side pieces, I need about five feet by two feet of a flexible plastic material which is easy to cut, like ABS or nylon. Is there a source someone here could recommend?

    OK, never mind that question. I found TAP Plastics online. They will sell "cut to order" plastic sheets.

    Nylon would be ideal, but they don't have it. My choices are PVC or ABS.

    PVC at a minimum thickness of 1/8" would not have the flexibility I need, plus it would be too thick when the foam and vinyl are applied.

    ABS they sell at a minimum thickness of 1/32" but I think that would be pushing it in terms of flexibility. I think 1/16" would do nicely, but they don't have that, either. My choices are 1/32", 3/32", 1/8", or incrementally greater. I will go with 3/32", I think. That should be about the thickness of the original cardboard, and also thick enough to hold the hardware I need to install into it (L-brackets, thread inserts, etc.).
    3.0L, automatic, carbureted

  8. #848
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    To quote James T. Kirk, "Well, that's... just... lovely."

    I finally got back to the replacement panel, and when I was drilling one of the holes, the drill bound up inside the plywood.

    SANY0171.jpg

    ... and it tore off the piece I had adhered to the back.

    SANY0172.jpg

    So that project is now ruined. I no longer have access to my friend's shop or equipment, because he's going to be too busy to help me over the next few weeks. So it looks like I will put the original damaged wood panel back inside the car. The confidence I had in myself which made me think that I could make a new console vanished instantly as soon as that back piece was ripped off. Nonetheless, I will go ahead and buy the plastic; as with all of my projects, the original pieces and parts will be kept on hand so that in the event of failure the stock parts can be put back on.

    Since Liquid Nails was unable to adhere two pieces of plywood together under the stress of a 3/8" drill bit, I doubt the same product would be strong enough to adhere a piece of wood to a fiberglass body shell under the stress of heat, humidity, and vibration. What adhesive would y'all suggest?
    3.0L, automatic, carbureted

  9. #849
    DMC Midwest - 815.459.6439 DMCMW Dave's Avatar
    Join Date:  May 2011

    Location:  Taylors SC

    Posts:    5,327

    My VIN:    (former)05429

    Club(s):   (DMWC) (DCUK)

    Quote Originally Posted by Farrar View Post
    Since Liquid Nails was unable to adhere two pieces of plywood together under the stress of a 3/8" drill bit, I doubt the same product would be strong enough to adhere a piece of wood to a fiberglass body shell under the stress of heat, humidity, and vibration. What adhesive would y'all suggest?
    That is surprising since they use it to hold houses together. Are you sure the plywood was clean?

    Windshield urethane is my default nevergonnacomeapart adhesive of choice, although I have not tried it on wood. Actually the most common wood glue is plain old (Elmer's) wood glue!
    Dave S
    DMC Midwest - retired but helping
    Greenville SC

  10. #850
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by DMCMW Dave View Post
    Are you sure the plywood was clean?
    Not really. I have never worked with plywood before, so I just followed intuition. I sanded it until it wasn't rough and blew it off with canned air, and made sure nothing came off on my hand when I touched it, but that's no guarantee.

    Perhaps I did not clamp the pieces together tightly enough. Either that or "project grade" Liquid Nails is not as good as the regular stuff. I just bought that variety because it was in a smaller tube and I did not want to be wasteful.

    I have made some progress.

    Vacuum hoses replaced with silicone:

    SANY0177.jpg
    SANY0178.jpg
    SANY0179.jpg

    As you can see, I also replaced the hard plastic vacuum tube with a silicone hose. From the tank in the left pontoon to the smaller hose at the HVAC control, it is now one continuous piece of silicone hose.
    3.0L, automatic, carbureted

Page 85 of 111 FirstFirst ... 35 75 83 84 85 86 87 95 ... LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •