FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 15 of 22 FirstFirst ... 5 13 14 15 16 17 ... LastLast
Results 141 to 150 of 220

Thread: Backlit Electronic Instrument Cluster

  1. #141
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by dmc6960 View Post
    Since the new cluster will operate strictly off of logic, it is a relatively simple manner to create two programs which will operate in normal or reverse. User selectable!
    With a jumper, I presume? Or am I thinking too old-fashioned?
    3.0L, automatic, carbureted

  2. #142
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Quote Originally Posted by Farrar View Post
    With a jumper, I presume? Or am I thinking too old-fashioned?
    Jumper or DIP switch.
    Jim Reeve
    DMC6960

  3. #143
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by dmc6960 View Post
    Yes, still progressing. No new good details to report yet. But certainly still progressing.

    On a side note, if anyone can figure out a way to obtain ONE or TWO of these chips...

    http://mcrmotorusa.com/IC%20Drivers.html

    Or compatible Switec M-S Quad Driver X12.017

    It would be a spectacular help. They should be the *key* to a good fluid needle. However the only manufacturer/distributor I've found of them or equivalents will only sell by the case. A box of 100 at $6.50 each. I dont want to buy the whole damn case until I know for sure I can get the electronics to work right. They've told me their "dealer" network only sells their stepper motors.

    So there's a little preview of the costs which will be involved in development of this. That box of 100 costing $650 will supply *ONE* component needed twice in each dash, enough for 50 dash units. Fortunately not many other components will have such a high minimum purchase requirement.
    Have you considered checking the junk yard for a car that might have this chip?

  4. #144
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Quote Originally Posted by stevedmc View Post
    Have you considered checking the junk yard for a car that might have this chip?
    A junk yard would not be a reliable way to procure 100+ chips for producing the cluster in numbers. If I was just doing for myself then yes.

    I have found alternatives to using this chip so it fortunately is no longer necessary. I'm just driving it strait off the PIC. A little extra programming never hurt anyone right?
    Jim Reeve
    DMC6960

  5. #145
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by dmc6960 View Post
    A little extra programming never hurt anyone right?
    Considering that there is a program out there to allow a TRS-80 Model 100 to read an SD card, I'd say you're right about that!

    Yesterday, I was under my dashboard doing some electrical stuff and found myself looking up at the underside of my gauge cluster. I immediately started thinking about this project.
    3.0L, automatic, carbureted

  6. #146
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by dmc6960 View Post
    A junk yard would not be a reliable way to procure 100+ chips for producing the cluster in numbers. If I was just doing for myself then yes.

    I have found alternatives to using this chip so it fortunately is no longer necessary. I'm just driving it strait off the PIC. A little extra programming never hurt anyone right?
    I just meant it would be a good way to get parts for the prototype. Any idea what this thing is going to cost? Are we talking hundreds of dollars, $500, or closer to a thousand? It looks awesome.

  7. #147
    Senior Member WelmoedJ's Avatar
    Join Date:  Jun 2011

    Location:  Purmerend, Netherlands

    Posts:    747

    My VIN:    06513

    Club(s):   (DCN)

    I have not yet cut into this discussion, however I'm very impressed with what I read and see.
    On DMCNews Hervey mentioned soon having a new unit that combines fuel pump and fuel sender into one unit.

    You may want to consider and contact him for details enabling you to incorporate another improvement into your project.

    Welmoed.
    Welmoed
    Black D 1981-11 sold
    Toyota Prius III 2009-07 (sold)
    Mazda MX-30 (BEV) 2020-09

  8. #148
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Quote Originally Posted by Farrar View Post
    Yesterday, I was under my dashboard doing some electrical stuff and found myself looking up at the underside of my gauge cluster. I immediately started thinking about this project.
    And the first thing you can do with that memory is forget everything! The back of the new cluster will be a nice clean PCB with one lamp socket (alternator), a few DIP switches, and accessory plugs for future functions/expansions...
    Jim Reeve
    DMC6960

  9. #149
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Quote Originally Posted by WelmoedJ View Post
    Hervey mentioned soon having a new unit that combines fuel pump and fuel sender into one unit.
    I tend not to do business with him anymore. Doesn't matter though, as he'll have to make his unit compatible with stock gauge which will by default work with mine.
    Jim Reeve
    DMC6960

  10. #150
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Quote Originally Posted by stevedmc View Post
    I just meant it would be a good way to get parts for the prototype. Any idea what this thing is going to cost? Are we talking hundreds of dollars, $500, or closer to a thousand? It looks awesome.
    If I could give you pricing right now I would. Just too many uncertainties still. Biggest factors will the the parts costs for stuff I need to have made for me. New cluster housing, new fascia, new needles, and perhaps more. Right now a whole new old stock cluster from DMC costs $328.13, or $578.13 for the metric one. It will be above those numbers, but I still have no idea how much higher.
    Jim Reeve
    DMC6960

Page 15 of 22 FirstFirst ... 5 13 14 15 16 17 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •