FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 34 of 37 FirstFirst ... 24 32 33 34 35 36 ... LastLast
Results 331 to 340 of 370

Thread: How to maintain your Delorean for less than $500 a year and put 10,000 miles on it

  1. #331
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Steve Rice needs to mentally add 150 miles driven with a rounded out dust cap to his odometer reading.

  2. #332
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    6,200

    Club(s):   (SEDOC) (DCUK)

    Use a drill motor...

  3. #333
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Unwinds the spindle cable (too many RPM's).

  4. #334
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    6,200

    Club(s):   (SEDOC) (DCUK)

    Use a variable speed drill motor...

  5. #335
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by Ron View Post
    Use a variable speed drill motor...
    Or just don't care. There are plenty of Deloreans out there that don't have working speedometers anyway.

    On another note, my speedometer finally started acting up again. For a few miles it started bouncing around and then started working perfectly again. This was about 200 to 300 miles ago. My guess is those plastic dust caps get tired of turning a piece of metal after 3 or 4 hours of nearly non-stop driving. Plastic becomes soft when it gets hot and I can imagine there is a lot of friction going on where the metal cable goes into the plastic cap.

    When I installed the new dust cap I could tell the angle drive cable was a little loose, but at the time it was able to stay in there without stripping anything. When I get home, I am going to take the angle drive cable and JB Weld it into the cap. Right now I'm in West Memphis and have no desire to go searching for a Walmart and Jack the car up. As of right now the speedometer is working fine but I wouldn't be surprised if it started acting up again tomorrow.

  6. #336
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Bill Robertson has a JB Welded dust cap. He made it by inserting a piece of smooth sided 1/8" square brass tube from a hobby shop into the JB Weld while it was wet, then pulling it out when the JB Weld had dried. It's a very snug fit on the spindle cable, but there is now absolutely no slop between his spindle cable and his dust cap whatsoever.

  7. #337
    Nit-picking customer(as seen on TV) Iznodmad's Avatar
    Join Date:  May 2011

    Location:  Lexington, NC

    Posts:    817

    My VIN:    #5000 (Grey, manual, SS chassis, intercooled twin turbo), #16128 (Grey, auto, efi twin turbo), #888

    Club(s):   (DCVA) (SEDOC) (DCUK)

    I'm glad you are making these posts about your intermittent angle drive. I too am having intermittent failures and I had convinced myself it was the dust cap only. I talked with another owner at the tech session and he said his AD was culprit from intermittent failure. My only other experience with AD failure was sudden and permanent. I was supposed to get a dust cap from Josh, but he sold the only two he brought with him to the tech session. Now I am more suspect of the AD itself. I have a replacement AD, perhaps I should just replace it and see if that solves the issue. I wish I would have gotten more done to my cars at the session. Dang.

  8. #338
    President, DeLorean Industries
    Join Date:  May 2011

    Location:  CLE/PHX

    Posts:    2,613

    My VIN:    5646,5080, 5880, 10234, 3639, 2518, 10586, 1538

    Quote Originally Posted by Iznodmad View Post
    I'm glad you are making these posts about your intermittent angle drive. I too am having intermittent failures and I had convinced myself it was the dust cap only. I talked with another owner at the tech session and he said his AD was culprit from intermittent failure. My only other experience with AD failure was sudden and permanent. I was supposed to get a dust cap from Josh, but he sold the only two he brought with him to the tech session. Now I am more suspect of the AD itself. I have a replacement AD, perhaps I should just replace it and see if that solves the issue. I wish I would have gotten more done to my cars at the session. Dang.
    I wish we could have stayed another day. We drove through the night because I scheduled a exhaust install at 10am on Sunday..... We are coming back that way for a number of cars. If we can time it with your schedule I can have Steve stop and address it for you.
    www.deloreanindustries.com Every Detail Matters

  9. #339
    Nit-picking customer(as seen on TV) Iznodmad's Avatar
    Join Date:  May 2011

    Location:  Lexington, NC

    Posts:    817

    My VIN:    #5000 (Grey, manual, SS chassis, intercooled twin turbo), #16128 (Grey, auto, efi twin turbo), #888

    Club(s):   (DCVA) (SEDOC) (DCUK)

    That is first class customer service Josh. Keep me informed please on the proper timing required. I'm also trying to enlist the help of Walter since he is in town for the rest of the week.

  10. #340
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by stevedmc View Post
    Bill's odometer currently reads 43K, but actual mileage on the vehicle is closer to 100K.
    Bill's odometer now reads 46K. He has driven 3,000 miles since DCS.

Page 34 of 37 FirstFirst ... 24 32 33 34 35 36 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •