FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 1 of 4 1 2 3 ... LastLast
Results 1 to 10 of 33

Thread: VIN: 2964 Engine: Electrical Wires Need Help!

  1. #1
    Senior Member 1batt4u's Avatar
    Join Date:  May 2011

    Location:  Queens, NY

    Posts:    1,307

    My VIN:    2964

    VIN: 2964 Engine: Electrical Wires Need Help!

    Hi all,

    I was looking over the wires in the engine!

    I took a few pictures, I want to see whats the story with these wires. I'm clueless!!


    1. Unplugged wire, it doesn't see to plug anywhere.


    2. Another unplugged wire in the back.


    3. By the hatch light switch, A connector with 3 cut wires, then a Red & Brown wires coming out for the blue connector just rapped together not connected to anything.



    4. I was wondering about this wire, if it is supposed to be going through that direction??



    5. Here is another wire, the blue wire goes down under the left(driver) side corner of the engine. I tried looking it was dirty/greasy, couldn't tell what it was.


    6. Here is the warm up regulator with the black hose, and has a "T" conector, connecting itto the other hose. Is that "T" connector wih the hole supposed to be there??


    If you guys can really help me out here, I really need the help!! I would really appreciate it!!!!

    Thank you all!!!
    Billy C. VIN: 2964

    "Trying to Live the Dream!"

    "If you're gonna own a DeLorean, why not build it with some style?"

    http://www.facebook.com/billy.chingas.7

  2. #2
    Senior Member 82DMC12's Avatar
    Join Date:  May 2011

    Location:  Olathe, KS

    Posts:    1,973

    My VIN:    11596

    Hi Billy, I know some of these....

    1. Those two white connectors should be connected.

    2. I think that connector is not used if you have a manual trans.

    3. Those look like the wires that go to the diagnostic plug. The bare orange wire is the one you use to check the lambda system with a dwell meter.

    4. I can check on that one in the morning. I think it goes in that general direction though.

    5. That red/white wire is supposed to go down to the starter solenoid to bring +12V to the cold start valve circuit. I'm guessing your cold start valve doesn't work.

    6. See the vacuum delay valve (the black cylinder with a white end that has vacuum hoses on either end)? The vacuum hose that is going down the top right corner of the picture is supposed to be connected to the T-hose. Do you have the vacuum hose diagram on your engine cover? Check that - it shows you how the vacuum hoses should be ran.

    I can help you with all of these tomorrow if you have more questions. Car is in the garage and I'm not going out again tonight :-) Looks like you have a lot of straigtening out to do. How does the car run? I'm guessing not very good with all the broken wires and vacuum leaks!

    Andy
    Andy Lien

    VIN 11596 Jan 1982 build - owned since Nov. 2000!
    Total frame-off restoration completed 2021-2023

    Photography and Backpacking is life.

    Was Fargo, ND
    Now Kansas City

  3. #3
    Senior Member 1batt4u's Avatar
    Join Date:  May 2011

    Location:  Queens, NY

    Posts:    1,307

    My VIN:    2964

    Here are a few more pictures!



    This is an alarm system one of the previous owners put in. The Black wire form the fuse turns into the Red wire, which runs under the fuse box into those wires there. There is a Grey wire, BLue & Green wire. What do I do in with these?





    Here is the alarm unit. You guys suggest I just cut off the wires and get rid of it?? No alarm ever worked when I got the car.





    This Box here?





    What is this device??





    Everything seems correct here?





    Here is the door lock upgrade from Toby! Is that the correct placeto put he yellow wire?





    I also was working almost all day trying to get the Wings-A-Loft together! No luck at all with that! :-(

    Goonna start a new seperate thread for the wings-a-loft! Look out for it!!
    Last edited by 1batt4u; 05-31-2011 at 01:09 AM.
    Billy C. VIN: 2964

    "Trying to Live the Dream!"

    "If you're gonna own a DeLorean, why not build it with some style?"

    http://www.facebook.com/billy.chingas.7

  4. #4
    Ryan > Ruben Ryan King's Avatar
    Join Date:  May 2011

    Location:  Fresno, CA

    Posts:    1,133

    My VIN:    3997

    #4 should be going to your Oil Sender unit? I would shrink wrap and solder it correctly.

    I would strongly suggest your remove the old door alarm system. Most, that I have seen, were not installed properly. I would gut it. I had an after market looking alarm system in my car, and it caused me a mess of headaches.
    Living The Dream Since 2005 - VIN#3997

  5. #5
    One of those purists you keep hearing about. sdg3205's Avatar
    Join Date:  May 2011

    Location:  Vancouver, BC

    Posts:    3,388

    My VIN:    thirty two 'o five

    Club(s):   (PNDC)

    +1 with Ryan.

    Dubious PO work should be removed IMO. It seems the vast majority is unsafe and makes the car less reliable. I'd rewire the car back to stock configuration and troubleshoot from there.
    Dave

    Here, somewhere.


  6. #6
    Senior Member Notifier's Avatar
    Join Date:  May 2011

    Location:  Earleville (Eastern Shore), Maryland

    Posts:    322

    My VIN:    802

    Club(s):   (DMA)

    The "alarm unit" in the second picture above looks like an old 12V lead acid battery!

  7. #7
    Senior Member 82DMC12's Avatar
    Join Date:  May 2011

    Location:  Olathe, KS

    Posts:    1,973

    My VIN:    11596

    Billy,

    I tried posting this correction the other day, but it might not have gone through. Anyway, I made a mistake.

    #2 - that connector hooks up to the connector that goes to the vacuum advance solenoid. It provides power to it. Since it's not plugged in, I'm guessing your vacuum advance doesn't work.

    #1 - Most people have all three of those connectors in a 'block' - they attach together like one big piece. Looks like you are OK there - the one connector doesn't go anywhere on manual trans cars.

    #4 is right. That's how the harness is normally ran. Some people have rerouted it to go under the intake manifold. Not sure if that's a good idea because it can get quite hot down there!

    Andy


    Quote Originally Posted by 82DMC12 View Post
    Hi Billy, I know some of these....

    1. Those two white connectors should be connected.

    2. I think that connector is not used if you have a manual trans.

    3. Those look like the wires that go to the diagnostic plug. The bare orange wire is the one you use to check the lambda system with a dwell meter.

    4. I can check on that one in the morning. I think it goes in that general direction though.

    5. That red/white wire is supposed to go down to the starter solenoid to bring +12V to the cold start valve circuit. I'm guessing your cold start valve doesn't work.

    6. See the vacuum delay valve (the black cylinder with a white end that has vacuum hoses on either end)? The vacuum hose that is going down the top right corner of the picture is supposed to be connected to the T-hose. Do you have the vacuum hose diagram on your engine cover? Check that - it shows you how the vacuum hoses should be ran.

    I can help you with all of these tomorrow if you have more questions. Car is in the garage and I'm not going out again tonight :-) Looks like you have a lot of straigtening out to do. How does the car run? I'm guessing not very good with all the broken wires and vacuum leaks!

    Andy
    Andy Lien

    VIN 11596 Jan 1982 build - owned since Nov. 2000!
    Total frame-off restoration completed 2021-2023

    Photography and Backpacking is life.

    Was Fargo, ND
    Now Kansas City

  8. #8
    Senior Member 82DMC12's Avatar
    Join Date:  May 2011

    Location:  Olathe, KS

    Posts:    1,973

    My VIN:    11596

    If you are talking about the white connector above the W-pipe, that's not correct. I think it has something to do with auto trans stuff. I have a manual so mine isn't used. I heard the explanation long time ago, don't remember, but I am positive it's not used on MT cars.

    Andy


    Quote Originally Posted by Ryan King View Post
    #4 should be going to your Oil Sender unit? I would shrink wrap and solder it correctly.

    I would strongly suggest your remove the old door alarm system. Most, that I have seen, were not installed properly. I would gut it. I had an after market looking alarm system in my car, and it caused me a mess of headaches.
    Andy Lien

    VIN 11596 Jan 1982 build - owned since Nov. 2000!
    Total frame-off restoration completed 2021-2023

    Photography and Backpacking is life.

    Was Fargo, ND
    Now Kansas City

  9. #9
    Senior Member 82DMC12's Avatar
    Join Date:  May 2011

    Location:  Olathe, KS

    Posts:    1,973

    My VIN:    11596

    Billy,

    The big black box sitting behind the driver's seat on the shelf that says Bosch on it and has two big white plug - that's the idle speed ECU. It tells the idle motor how to operate.

    The picture below it, of the silver box pointing downward with the wide black connector on it, that is the Lambda ECU. It takes readings from the Lambda/O2 sensor, determines how much oxygen is in the exhaust, figured out if the car is running rich or lean, and then adjusts the frequency valve duty cycle to compensate.

    Both boxes are OEM and I don't see anything odd about those pics.

    Andy
    Andy Lien

    VIN 11596 Jan 1982 build - owned since Nov. 2000!
    Total frame-off restoration completed 2021-2023

    Photography and Backpacking is life.

    Was Fargo, ND
    Now Kansas City

  10. #10
    Senior Member 1batt4u's Avatar
    Join Date:  May 2011

    Location:  Queens, NY

    Posts:    1,307

    My VIN:    2964

    So here are more pictures of screwed up wiring!! One of the previous owners had some alarm system on the car along with a back up battery. Wiring is all over the place, tapped into dome lights, fuse box, engine compartment. I gotta figure all this out!! CRAZY! Along with the fuel pump and rest!!
    Who ever did all this really screwed with the car!!!!

    1. This is a 12V lead acid battery, to the left of the Lamda ECU. Part of the alarm system which is directly under, in the driver side compartment.


    2. Here is the alarm unit. Damn you!!! Wires all over the place, tapped into the front under the dash, the dome lights, fuse area, engine area.


    3. Wire from the alarm system going to engine, then in the engine, wires are all cut up, very long red and black wires all tied up and lead to no where. One wire tapped into black wire which goes to the metal box right on top to the left



    4. DO these wires look as if they belong there, or is it part of the alarm system?? The colored wires with the Blue connector


    5. Alarm Wire, driver side foot well. Red wire from alarm connected to LH dome light switch, and to a grey wire which goes to passenger side dome light switch. I think I will leave the grey wire so I can connect the wire for the Wings-A-Loft system from thge driver side!



    6. Here is something else. A Red/Brown wire tapped into by a brown which goes into I guess a fuse then out a Green wire. Couldn't really see where the Green wire went.


    7. Here are more pictures of the fuel pump, found the stock wire and plug.


    8. Black wire on the plug is cut off as well as the Beige/brown and has a yellow cap on it. The fuel sender unit plug, Red and Orange are plugged to the sender unit, there is a black on not connected to anything. Any idea??


    Really hope you guys can help me with this one!! I have a project with the car itself fixing all the fail parts, worn out parts, ect... Now I gotta fix all this mess from the previous person!! Sucks!!
    Last edited by 1batt4u; 06-03-2011 at 01:40 AM.
    Billy C. VIN: 2964

    "Trying to Live the Dream!"

    "If you're gonna own a DeLorean, why not build it with some style?"

    http://www.facebook.com/billy.chingas.7

Page 1 of 4 1 2 3 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •