FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 1 of 5 1 2 3 ... LastLast
Results 1 to 10 of 42

Thread: Frustrating Fuel Problem!

  1. #1
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    Frustrating Fuel Problem!

    Here we go again - I go from trying to fix my cold start valve to now my fuel pump. Weeks ago I could start my car (after pouring gas down the intake) and drive off into the sunset. I fixed my cold start valve and after that, my fuel pump wont work. It will come on after I let the car sit for a while - I can jump the RPM relay and it is on but as soon as I turn the key to engage the starter it shuts off! I unplug the jumper for the RPM relay and it sparks showing that there is voltage going to the pump, but it just doesn't run. I can take the pump out, hook it to a battery and it will run all day. What the hell? I took everything out of the tank and cleaned everything including the tank - the filter (which isn't dirty after many years-thanks John Hervey) and everything else in there.... My bulkhead connectors are clean and making contact now even though they will soon be replaced. What am I missing? I'm in this now about 5 hours and a six pack... My fuel pump is old, maybe 4 years but it has never missed a beat. I am running the one ballast resistor (everything was from SpecialT) and I did wrap up the wiring with new tape but didn't mess with any connections aside from cleaning. Any thoughts?

  2. #2
    Senior Member
    Join Date:  May 2011

    Posts:    1,315

    My VIN:    03238 Grey & Black Hybrid - Auto - work in progress Former owner 10902 - Universal 93 Raffle Car

    I'd guess low voltage/bad connection to the fuel pump.

    Read through this thread...

    http://dmctalk.org/showthread.php?10...highlight=fuel

    Check your voltage at the rpm relay, at the fuel pump with the relay jumpered, and during actual cranking...

  3. #3
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    I'm getting an average of 8 volts with the pump running and then it turns off - measured the voltage once off and it is between 6-7 volts so obviously it isn't enough to sustain operation. I'm going to do the suggested things in the post you linked, I appreciate it! Thanks for the help.

  4. #4
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    Wow, fixed already... Should have posted hours ago! I added a ground to the inertia switch and the voltage shot up to almost 12. At least the fuel tank is clean and I know the condition of my fuel system after years. I feel great now, Thanks again!!!

  5. #5
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    A couple of owners who run low pressure fuel pumps have been reporting pump motor problems as well. I am beginning to think their problems are also related to the inertia switch, especially since owners who have bypassed their inertia switches (I'm not advocating doing that -- just saying that they have) are not reporting similar problems with the same model pumps. The inertia switch is a troublesome ground point that sometimes even melts the harness connector.

    Bill Robertson
    #5939

  6. #6
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,635

    My VIN:    03572

    Quote Originally Posted by dn010 View Post
    Wow, fixed already... Should have posted hours ago! I added a ground to the inertia switch and the voltage shot up to almost 12. At least the fuel tank is clean and I know the condition of my fuel system after years. I feel great now, Thanks again!!!
    Where did you add the ground?
    Dave M vin 03572
    http://dm-eng.weebly.com/

  7. #7
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    Where I added the ground - I already had a good size ground wire that was running from the frame that holds the Lambda counter - to the frame of the car. I ran this wire years ago when I installed my car alarm. I forgot about this ground location - so all it took for me was a spice from the inertia switch ground wire to this location. I even had a heavy gauge wire installed there already for some reason so it took less than 30 seconds to complete this ground.

    It is a shame, I think if I kept driving my D I would have much less problems, no wonder D's that sit are a mess, mine sat for almost 2 years (indoors no less!) and I'm having all kinds of issues and it was a daily driver with no problems prior.

    Bill - perhaps the low pressure leads to the fuel pump breaking down... I was one of the few who - years ago - wanted to convert to a carb like you (we had many discussions about it on and off the DML), I just lacked the funds to buy a damn manifold. A ground issue is a ground issue, but I'll bet you have many less issues than us K jetters. Maybe one day.....

  8. #8
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Quote Originally Posted by dn010 View Post
    I'll bet you have many less issues than us K jetters. Maybe one day.....
    Ground issues plague everybody, irrespective of fuel delivery. And while the carb itself only needs to ground the choke heater, as you can see, several owners are struggling with fuel pumps at the other end of the car. Other ground issues are of course common to everyone.

    I have fewer problems because my car has a 4 gauge cable running from the front radiator bracket to the top of the engine (with a side branch to the negative battery terminal) into which every ground point is tied.

    Bill Robertson
    #5939
    Last edited by content22207; 08-21-2011 at 10:08 PM.

  9. #9
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    Quote Originally Posted by content22207 View Post
    Ground issues plague everybody, irrespective of fuel delivery.

    Hence the "ground issue is a ground issue", there isn't much you can do to escape this on a car that is exposed to elements which will corrode plus the poor ground design to begin with that I've been reading about...


    I have fewer problems because my car has a 4 gauge cable running from the front radiator bracket to the top of the engine (with a side branch to the negative battery terminal) into which every ground point is tied.

    Bill Robertson
    #5939
    I've had my frame off twice, the next time it is off (need a new frame) I will run a ground wire up like this, it is an excellent idea.

  10. #10
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by dn010 View Post
    I've had my frame off twice, the next time it is off (need a new frame) I will run a ground wire up like this, it is an excellent idea.
    Hearing stuff like this is convincing me to run a full length ground wire like Bill more and more each day. I have been thinking about doing it for a while but I am just lazy and have a huge to do list as it is. I don't think you need to wait until it is off the frame though. Bill did his and I think his frame has never been separated from the body.

Page 1 of 5 1 2 3 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •