FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 2 of 5 FirstFirst 1 2 3 4 ... LastLast
Results 11 to 20 of 42

Thread: Frustrating Fuel Problem!

  1. #11
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Quote Originally Posted by dn010 View Post
    I've had my frame off twice, the next time it is off (need a new frame) I will run a ground wire up like this, it is an excellent idea.
    A ground bus needs to run through the interior of the vehicle, otherwise you can't tie into it (the frame itself already is a giant bus -- you just can't get to it because there's a fiberglass body in the way):
    GroundBusConsoleAnnotated.jpg GroundBusRelayBoltAnnotated.jpg

    Bill Robertson
    #5939

  2. #12
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,635

    My VIN:    03572

    Quote Originally Posted by dn010 View Post
    Where I added the ground - I already had a good size ground wire that was running from the frame that holds the Lambda counter - to the frame of the car. I ran this wire years ago when I installed my car alarm. I forgot about this ground location - so all it took for me was a spice from the inertia switch ground wire to this location. I even had a heavy gauge wire installed there already for some reason so it took less than 30 seconds to complete this ground....
    Did you happen to see if your dash voltmeter indicates a higher voltage now that you run that frame ground to the fuel pump?
    Last edited by Bitsyncmaster; 08-22-2011 at 06:42 AM.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  3. #13
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    Bill - I see how you did the wiring now, seems like the best way. I was going to run a ground up the frame and tap into different areas inside the car (like I did with the Lambda counter frame) but it seems much more involved then what you have there. Thanks for the pictures.

    As far as the car indicating a higher voltage - maybe slightly but...not really. My voltage runs slightly under the "13" mark so it's obvious this isn't my only issue with grounds. I've seen folks running between the 13 and 15.5 volt mark which is where I'd like to be. For the fuel pump ground I'm also using a gauge wire that is significantly smaller than what Bill is using and Dave M is using in his post (I think he used 10AWG) so once I am able to get the correct wire in there, I'll let you know my findings. I just hooked it up this way so the car would run. I am also planning on not only running a main ground wire up to the front of the car, but also one that will run directly to the engine so I can get rid of that ground strap.

  4. #14
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,635

    My VIN:    03572

    Quote Originally Posted by dn010 View Post
    As far as the car indicating a higher voltage - maybe slightly but...not really. My voltage runs slightly under the "13" mark so it's obvious this isn't my only issue with grounds. I've seen folks running between the 13 and 15.5 volt mark which is where I'd like to be. For the fuel pump ground I'm also using a gauge wire that is significantly smaller than what Bill is using and Dave M is using in his post (I think he used 10AWG) so once I am able to get the correct wire in there, I'll let you know my findings. I just hooked it up this way so the car would run. I am also planning on not only running a main ground wire up to the front of the car, but also one that will run directly to the engine so I can get rid of that ground strap.
    If that frame ground fixed your fuel pump then you must have a bad ground still. I'm not sure what other things are common to that original ground. Yes I did use 10 AWG wire for my new pump ground, but that only brought the fuel pump voltage up about 0.4 volts. I did note my dash voltage gauge reads higher now (almost 15 volts) so I assume that ground was common to the dash also.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  5. #15
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    So far, I ran a new ground wire from my relay compartment (not hooked up yet) to the radio frame. I've crimped and soldered all the grounds from that frame to the new ground wire. This evening I'd like to finish by running a ground wire from the relay compartment to the frame (battery ground) and then from the frame to the transmission or engine. I think it would probably be a good move for me to check out the connector by the washer fluid bottle and clean the grounds on the frame extension so I'll get that done while I'm at it... I'll fire up the D and see what my voltage is once this is all complete - I'll be happy if I'm actually getting the correct voltage finally, then I can start troubleshooting other problems with one issue crossed off the list of possible causes!

  6. #16
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Just attach the wires formerly ganged on the radio bracket to your bus *NEAR* the bracket. Use a nut & bolt to hold everything together so you can add new grounds to the bus as necessary (additional cigarette lighters, heavier radio ground, etc).

    BTW: All those wires on the radio bracket except one are grounds in. There is only one wire leaving the radio bracket towards the rear of the car, and it is only 16 gauge -- yet another example of how badly these cars were grounded new from the factory.

    If you want to extend your bus through the firewall you will need to drill a hole. The firewall is so thick, you won't need a grommet if you drill the hole the exact same diameter as your wire (solder the end on inside the car after you've run the wire through the firewall). My bus goes all the way to the front radiator bracket:
    GroundBusFrontRadiator.jpg
    (That 8 gauge wire extends the bus to the stainless bar across the front of the car, which I used as a grounding block for the two ground junctions behind the headlights. It does not have any inline connectors by the washer bottle -- if I ever need to separate the body from the car I will undo it at the radiator bracket and let it stay with the body).

    Bill Robertson
    #5939

    Quote Originally Posted by dn010 View Post
    So far, I ran a new ground wire from my relay compartment (not hooked up yet) to the radio frame.
    Don't forget there are three ground junctions underneath the console that need to be tied into your bus (circled in my earlier pic).

    My bus runs to the ECU compartment first, then branches to the relay compartment and the engine:
    GroundBusEcuBlockAnnotated.jpg

    Bill Robertson
    #5939
    Last edited by content22207; 08-23-2011 at 10:57 AM.

  7. #17
    Senior Member AdmiralSenn's Avatar
    Join Date:  May 2011

    Posts:    443

    I will add another vote for the ground bus. I never really had any serious grounding problems with my accessories or fans or anything but I did notice that my voltage gauge started reading accurately after I installed the bus, and things just seemed less "quirky". It's WELL worth the effort.

  8. #18
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,635

    My VIN:    03572

    Quote Originally Posted by content22207 View Post
    BTW: All those wires on the radio bracket except one are grounds in. There is only one wire leaving the radio bracket towards the rear of the car, and it is only 16 gauge -- yet another example of how badly these cars were grounded new from the factory.
    Bill Robertson
    #5939
    The British wiring standard does not use 16 AWG. In my endeavors into the D, the wiring seems to us 18 AWG with the exception of very high currents.

    British 14 strand wire = 18 gauge US
    British 28 strand wire = 14 gauge US
    British 44 strand wire = 12 gauge US
    British 65 strand wire = 10 gauge US

    I'm going to pull my center console and find where that original ground off the crash sensor goes. If it goes to that one ground Bill has found.....what were they thinking (drinking).
    Dave M vin 03572
    http://dm-eng.weebly.com/

  9. #19
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Quote Originally Posted by Bitsyncmaster View Post
    The British wiring standard does not use 16 AWG. In my endeavors into the D, the wiring seems to us 18 AWG with the exception of very high currents.
    Even worse.

    Where is good old fashioned American 12 gauge wire when you need it?

    If only JZD had turned to Kenosha for engineering expertise....

    Bill Robertson
    #5939

  10. #20
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    I can not emphasize enough *NOT* to forget the three ground junctions underneath the console (heat shrunk from the factory -- peel it off). If you only ground the radio bracket to the relay compartment, you haven't accomplished much (you haven't really done anything that couldn't also be accomplished by simply running a wire from that bracket to the body bolt directly underneath it.

    I tied my console junctions into the bus with copper terminal lugs. Insulation was stripped off the bus wire at the appropriate places, lugs slid over it, then tightened to press the junctions against the bus. The terminal screws were lock tighted, cut off flush with the lugs, then the whole arrangement wrapped in poor man's heat shrink (electrical tape and a heat gun -- see the ring terminal in my radiator bracket pic).

    I also used terminal lugs to attach the ground junction inside the relay compartment, and two smaller ones to attach short jumpers between the junctions behind the headlights and that big stainless bar (I use the bar as a ground block, just like the block in my ECU compartment).

    Bill Robertson
    #5939
    Last edited by content22207; 08-23-2011 at 11:13 AM.

Page 2 of 5 FirstFirst 1 2 3 4 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •