FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 3 of 5 FirstFirst 1 2 3 4 5 LastLast
Results 21 to 30 of 42

Thread: Frustrating Fuel Problem!

  1. #21
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    These are the ground junctions that also need to be tied into a bus:

    Near the rear bulkhead connectors:
    GroundBusBulkheadConnectors.jpg

    Bulkhead bolt itself:
    GroundBusBulkheadBolt.jpg

    One inside the relay compartment:
    GroundBusRelayCompartment.jpg

    Under the console in the rear (driver's side):
    GroundBusConsoleRear.jpg

    Under the console, in the middle (passenger side):
    GroundBusConsoleMiddle.jpg

    Under the console, in the front (very close to the radio bracket):
    GroundBusConsoleFront.jpg

    I mounted a block with a 1/4" stud in the ECU compartment to easily add new grounds, or anything I've overlooked, in the back of the car (I also have a bolt in the relay compartment, but it's 3/8" diameter -- I just use the metal superstructure, to which that bolt is attached, as a block for relays, etc).

    Former radio bracket grounds are attached to the bus with a 1/4" nut & bolt. Any new grounds or anything I've overlooked in the front of the car (I am debating whether to run a new wire to the dashboard bolt by the glove box -- doesn't seem necessary at this time) can be added to the bus there.

    Bill Robertson
    #5939

  2. #22
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Remember also that a ground bus is pretty much useless unless it has its own independent connection to the battery:
    GroundBusBattery.jpg

    Bill Robertson
    #5939

  3. #23
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    Man, I think I would have botched this if it wasn't for these posts (or at least had this so it wasn't entirely efficient). Thanks for the pictures and all the info; looks like I have much more work ahead of me, I'll have to run to the parts house for more electrical items after work!

  4. #24
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    My terminal lugs came from Lowes. I think I have one left over that can be photographed (or I can take The World's Cheapest Digital Camera to the store).

    Those ground junctions are most likely just like the radio bracket -- a bunch of wires in, but only one wire out. That is why I tied them into my bus.

    Bill Robertson
    #5939

  5. #25
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    A ground bus only costs about $30-$40 -- less than one single stainless steel DMC logo bauble. There is no more cost effective upgrade an owner can make to his or her car.

    Bill Robertson
    #5939

  6. #26
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    How much wire (length) do you think you went through?

  7. #27
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Don't forget that, unless you own them already, you will have to buy the necessary tool to crimp battery lugs, or a torch and solder (or both).

    Farrar
    3.0L, automatic, carbureted

  8. #28
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    I have a large set of crimps designed for heavy gauge wires, I think down to 4; they were around $200 bucks when I had to get them as a mechanic so those should do the trick. However, there are some connections that I would like to solder - luckily I have those tools too

  9. #29
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    Also - Bill, you used 8 gauge, Dave used 10 gauge... this may be a stupid question but is there any benefit in using the one over the other in our setting? I am using 8 gauge, but I am just curious at this point... And maybe the answer will help steer future readers while doing this upgrade.

  10. #30
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by dn010 View Post
    I have a large set of crimps designed for heavy gauge wires, I think down to 4; they were around $200 bucks when I had to get them as a mechanic so those should do the trick. However, there are some connections that I would like to solder - luckily I have those tools too
    Ouch, that sounds like an expensive tool for doing such a cheap job. I really would like to do this but don't want to fork out $200 for tools. I have a feeling someone could make a nice chunk of change selling kits for this.

Page 3 of 5 FirstFirst 1 2 3 4 5 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •