Bill,
There's a ground wire behind the panel that covers the fuel fill hoses.
The wire is attached to a bolt that runs through the "firewall" and connects to the pedal box.
I have traced this wire to be the ground for the fuel sender.
Welmoed.
Location: Purmerend, Netherlands
Posts: 747
My VIN: 06513
Club(s): (DCN)
Bill,
There's a ground wire behind the panel that covers the fuel fill hoses.
The wire is attached to a bolt that runs through the "firewall" and connects to the pedal box.
I have traced this wire to be the ground for the fuel sender.
Welmoed.
Welmoed
Black D 1981-11 sold
Toyota Prius III 2009-07 (sold)
Mazda MX-30 (BEV) 2020-09
Yes it's just the dash volt gauge that sees that ground offset caused by the fuel pump current (and now maybe the blower current) that makes it read lower. What your doing with the large ground buss should fix it. But my plan is just to make those two large current grounds move to the frame. Then the original ground wire only has to conduct the light ground currents and hence not offset the dash gauge.
I have already put the inertia switch ground to it's own frame ground. Now I will move the blower ground to it's own frame ground. I would do the same, run a 10 AWG wire to the shifter mount bolt. This should increase the blower motor voltage a little also.
edit:
Actually all the dash gauges are seeing the offset but it seems the most affected gauge is the volt gauge.
Last edited by Bitsyncmaster; 08-25-2011 at 06:20 AM.
Location: Staten Island, NY
Posts: 256
My VIN: 3501
Club(s): (DMA)
If it helps I have my video of the wire harness breakdown here:
http://youtu.be/_IND69PZ6C4
Posts: 1,068
While poking around under #5939's dash I realized a few errors from the front junction. This is a corrected copy:
DeLoreanGroundsInProcess4.jpg
I still hope to trace out the relay compartment grounds later today.
Bill Robertson
#5939
Posts: 1,068
The headlights (and side/front marker lights) go directly to the bulkhead bolt, thence to the frame.
Bill Robertson
#5939
Great work Bill. A suggestion if I may...
Put a pass-through of the inertia switch with perhaps a dashed line leading through the washer bottle connectors to the fuel pump. Its an important enough circuit I feel the complete path should be mapped.
Jim Reeve
DMC6960
Posts: 1,068
Purple/Black is a switched ground. It's no different in principle than Purple/White. This schematic shows black wires only. Any wire you ring out on this schematic should beep to the negative battery terminal.
Bill Robertson
#5939
Posts: 1,068
As a world renown Nazarene once said, it is finished:
DeLoreanGroundsFinal1.jpg
Actually I have labeled this file "Final1" because there are still at least three unknowns/assumptions subject to change:
1) The large gauge wire from the junction behind the A/C central duct is assumed to be the the windshield wiper motor -- until I figure out where the damn thing is and can visually verify it, that is subject to change. The second large gauge most likely is the inertia switch because it has the same gauge wire attached. The third large gauge wire was verified all the way back to the bulkhead bolt by unwrapping the harness. I unfortunately can not unwrap the harness forward to trace the other two large gauge wires because it disappears between a metal superstructure and the dash.
2) The small gauge wire to the wiper delay module continue somewhere (annoying door buzzer perhaps?). I do not have annoying door buzzers in either of my cars, so I can't verify that.
3) The small gauge wire that disappears by the windshield is assumed to be the wire that emerges from underneath the windshield trim and is attached to the fender -- I haven't pulled the trim off yet to verify.
All other wires were visually verified by unwrapping the harness and following them to see where they go. I am now the proud possessor of a DeLorean with no front suspension (or condensor/radiator/fans), no fuel delivery system, no interior, *AND* a whole lot of loose wires. Anybody want to come over with a couple rolls of electrical tape and help me put this thing back together?
So there you have it. The next time someone laments that they have no idea where something is grounded on these stupid little cars, just point them to this thread.
Bill Robertson
#5939
Posts: 1,068
Well that didn't last long....
First revision:
- Redraw glove box switch and passenger door plunger to more clearly represent that the wires are ganged
- Change "Useless Bolt" to "Dashboard Bolt" (I was hot, tired, and irritable when I wrote that)
- Add sidelights to the *ONE* 16 gauge ground wire from the back of the car (what was Lotus thinking?)
DeLoreanGroundsFinal2.jpg
Bill Robertson
#5939
DMCTalk is automatically downsizing my original (1300 x 1600 pixels). If you want a larger copy, shoot me your eMail address.
Bill Robertson
#5939