FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 4 of 6 FirstFirst ... 2 3 4 5 6 LastLast
Results 31 to 40 of 60

Thread: DeLorean Ground Schematic

  1. #31
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    If the harness changed, if was after VIN 5939 (both of my cars have a junction behind the central A/C duct).

    I never paid too much attention to that bundle of wires on the radio bracket until this project. Both #2508 and #5939 have nothing but capacitors and the radio on it.

    I suspect people assumed the instrument cluster was grounded to the radio bracket because the ground junction behind the central A/C duct is virtually impossible to see. I had no idea it was back there. When I tied #5939's junction into its ground bus I had to do all the work by braille -- that's how hidden it is. There are only 3 ground wires coming down the driver's side of the console, so the binnacle was obviously grounded somewhere north of the radio bracket. I guess people just assumed that one of those wires had to be it (two wires actually -- there are two grounds from the binnacle/instrument cluster).

    I am open to changing the schematic, but only if the changes are proven by visual inspection. I ripped all the wrapping off #2508's harness to make it. Nearly every single wire was individually traced. There are only a couple of assumptions in the current revision:
    - Individual ground wire that disappears into the dash by the passenger windshield corner (not the A pillar bundle) is assumed to the the same wire that emerges from underneath the exterior trim piece and is bolted to the fender
    - Third large gauge wire leaving the junction behind the central A/C duct is assumed to be the windshield wiper motor. I have yet to find the motor to verify that it does indeed have a large gauge wire attached to it (where is the damn thing?)
    - Every small wire leaving the junction behind the central A/C duct is accounted for. There is a ganged small gauge wire leaving the plate that holds the windshield wiper delay module going somewhere.

    The wiring harness up & over the steering column is the only one I did not unwrap, because it is sandwiched between the metal superstructure and the dash (inaccessible). I did unwrap the harness where it passes through the firewall towards the windshield washer bottle -- there are only two large gauge ground wires in it at that point.

    Believe it or not, I traced every inch of the two black wires from the Lambda ECU to the bulkhead connectors, including unwrapping the bundles all the way through the plywood bulkhead (twice!). That's no small feat. I had to do it -- those wires were obviously present in different locations but unaccounted for. I physically followed each wire to see where they went. I have no idea what they do, or even if they are in fact grounds, but that is definitely where they go (verified this morning by ringing them out with a meter).

    The cigarette lighter ground is a tricky one. The wire starts towards the front of the car, then about 4-6 inches later makes a U turn back to the harness that goes to the rocker switches. Unless you unwrap the entire harness it looks like two different wires.

    Bill Robertson
    #5939

    Quote Originally Posted by sean View Post
    Ok, Bill, the one you have uploaded seem proper to me as when I upload this guy I can click on him and he expands. Does this not work for others? You actually have to click on him twice to make it expand.

    Attachment 4516
    Still 840x1030.

    This is what my 1300x1595 working copy looks like split down the middle:
    DeLoreanGroundsFinal4Left.jpgDeLoreanGroundsFinal4Right.jpg

    Bill Robertson
    #5939

  2. #32
    Senior Member
    Join Date:  May 2011

    Location:  New Jersey

    Posts:    233

    My VIN:    ******* 01860 - Legend TT 06068 - VQ35 SC

    Club(s):   (DMA)

    Quote Originally Posted by content22207 View Post
    - Third large gauge wire leaving the junction behind the central A/C duct is assumed to be the windshield wiper motor. I have yet to find the motor to verify that it does indeed have a large gauge wire attached to it (where is the damn thing?)
    It is above the pedal box..
    __________________________________________________ ____________________
    Got any new Purflux oil filters? I may want to buy them.
    Learn about Vin 01860 with a Legend Industries engine: https://malevy-dmc.blogspot.com/2022...oDeLorean.html
    I can fix your Craig W460 radio: https://malevy-dmc.blogspot.com/2022...te-player.html

  3. #33
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    6,200

    Club(s):   (SEDOC) (DCUK)

    Quote Originally Posted by sean View Post
    Does this not work for others? You actually have to click on him twice to make it expand.
    In post- 81x100
    Click to Expand- 411x504
    Click Twice- 411x504 but in own window
    Drag to PS Pro- 839x1030

    -Good Job Bill

  4. #34
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Just remembered that I grabbed the ground that previously went to the shifter illumination bulb for another use. Sure enough -- it's bloody stump is still in the middle ground junction (just unwrapped it for visual verification).

    As stated, this is still a work in progress. I am open to changes, but they need to be physically verified, not just conjectured:
    DeLoreanGroundsFinal5.jpg

    Bill Robertson
    #5939

    Actually that bloody stump may be for the Fan Fail/Lock Door/Defroster bulbs. I've thrown #2508's bulbs away. AFAIC they are nothing more than an impediment to console removal. I'm a big boy -- I can lock my own doors. The fan fail light doesn't do anything if you run a jumper in the fan fail socket. And I don't use the rear window defroster because it has a blistering hot engine sitting directly underneath it (has anybody ever had their back window covered with ice?).

    Anyway, could somebody with those bulbs intact please verify whether or not they are grounded through the middle junction on the passenger side.

    I am going outside (in the rain) to unwrap the rear junction on the driver side to see if it has a bloody stump. I seem to remember the shifter illumination bulb going up that side of the harness.

    Edit: No bloody stump. I am almost positive the shifter illumination bulb used to come from the driver's side of the harness. Could someone with an unmolested car trace the shifter illumination bulb ground? I'd like to keep this schematic as accurate as possible.

    Bill Robertson
    #5939

    Almost finished for real this time.

    Took the console back out of #5939, which still has the warning bulbs that used to be in its A/C panel (coiled up and pushed out of the way). It also has the shifter bulb line. There are eleven small gauge ground wires coming out the the middle passenger side junction, all accounted for now:
    DeLoreanGroundsFinal6.jpg

    As soon as I figure out where the wire that is ganged onto the wiper delay chassis goes, every single ground wire north of the bulkhead bolt will have been traced.

    Bill Robertson
    #5939

    Apparently the DML is better than DMCTalk after all -- it lets you upload bigger files: http://f1.grp.yahoofs.com/v1/0DtaTvD...undsFinal6.JPG

    Bill Robertson
    #5939

  5. #35
    Nothing witty here lest it offend
    Join Date:  May 2011

    Posts:    990

    For us nonmechanical types, is it fair to conclude from these threads that
    1) The cars systems were designed in isolation and then quickly married
    And therefore
    2) The car has twice as much wiring than it should have

    Or am I wrong. The rest of us wouldn't mind some general conclusions about what your detective work means in terms of their theory of wiring this car.

  6. #36
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Given the information in this schematic I would say that the average owner should at least ground the inertia switch to a body bolt. This would be easy enough to do: remove the shifter cover plate and there's your bolt. Now just ground that junction to that bolt using a suitably large wire, perhaps 10-gauge.

    ... In fact, I think I might do this before I start driving the car on my new fuel pump. Although I like the idea of a ground bus, I don't have the wherewithal to make my own ground cables. (It's a shame, since I already bought the cable and lugs -- anybody wanna buy some 6-gauge black battery cable and copper lugs from me?)

    Farrar
    3.0L, automatic, carbureted

  7. #37
    Senior Member AdmiralSenn's Avatar
    Join Date:  May 2011

    Posts:    443

    Really? It's not hard. Propane torch, heat up terminal, fill with solder, insert cable, allow to cool, crimp. I just finished mine.

    The hard part is spending the money, the rest is easy.

  8. #38
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Quote Originally Posted by SamHill View Post
    The rest of us wouldn't mind some general conclusions about what your detective work means in terms of their theory of wiring this car.
    1) It sure is helluva lot easier to ground devices on a metal bodied car (can I hear an "Amen" from the Corvette owners).
    2) DMC obviously never meant the ground junctions to be user serviceable, otherwise they wouldn't have hidden the most important one in the most inaccessible location.
    3) Ganging the instrument cluster with a bunch of other devices, especially the intermittent wiper motor, was a bad idea.
    4) Only one 18 gauge ground wire for all the rear bulbs was another bad idea.
    5) Empirical evidence indicates the front driver side grounds are inadequate:
    - Melted inertia switches
    - Melted fuel pump fuses
    - Erratic instrument cluster behavior
    6) There are only seven 12 gauge ground wires for all the electrical devices north of the rear bulkhead (plus the rear lights, and a couple of engine mounted devices) -- a mere fraction of the copper in all those positive leads. If the ground wires are in fact adequate, they are just barely so, with no margin for connection degradation.
    7) Almost the entire car depends upon the cable that goes from the bulkhead bolt to the frame. If you're going to clean anything, clean it (DeLorean owners seem to be disproportionately preoccupied with the radiator bracket bolt).
    8 ) On the new & improved DMCTalk, if you put an "8" and a close parenthesis next to each other the site automatically reformats them into a smiley face.
    9) Conventional wisdom that the instrument cluster is grounded via the radio bracket is just plain wrong.
    10) As bad as Fords are, their wiring still runs circles around a DeLorean.

    I'll add more as I think of them.

    Bill Robertson
    #5939

    Quote Originally Posted by AdmiralSenn View Post
    Really? It's not hard. Propane torch, heat up terminal, fill with solder, insert cable, allow to cool, crimp.
    Alternative method: drill a small hole for solder to flow through, flux the inside of the connector, insert cable, heat with a torch, flow solder in.

    Bill Robertson
    #5939

  9. #39
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    Quote Originally Posted by AdmiralSenn View Post
    Really? It's not hard. Propane torch, heat up terminal, fill with solder, insert cable, allow to cool, crimp. I just finished mine.

    The hard part is spending the money, the rest is easy.



    That's how I did mine, I think I posted this method earlier but it is very quick and easy, and it holds even without a crimp should you choose not to.

  10. #40
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by dn010 View Post
    That's how I did mine, I think I posted this method earlier but it is very quick and easy, and it holds even without a crimp should you choose not to.
    Gas cylinder: $11. Soldering/brazing torch: $35. Battery crimp tool: $231.

    Soldering method looks a lot better to my wallet.

    Farrar
    3.0L, automatic, carbureted

Page 4 of 6 FirstFirst ... 2 3 4 5 6 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •