FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 955 of 956 FirstFirst ... 455 855 905 945 953 954 955 956 LastLast
Results 9,541 to 9,550 of 9553

Thread: What have you done to your DeLorean today?

  1. #9541
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    I got my LEDs. They are bidirectional but I'm having a hard time to get reliable connection in the sockets to LEDs. I've tried to bend the pins tighter in the sockets with no results. Maybe I need to sand the wires on the LEDs.

    I did install the new flex PCB. The old one was still working but most of the laminate has separated.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  2. #9542
    Senior Member
    Join Date:  Dec 2016

    Posts:    512

    How about some DeoxIT on the contact points and sockets?
    Ron

  3. #9543
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    Binnial LEDs

    I found the problem with the socket random connection. Oxidation on the clamping where the LED presses in. It's a white power type oxidation. One socket is really bad all others have just a little. I wonder what causes that oxidation.

    I'm thinking of using the sockets to hold the bulbs but soldering the LED wires to the PCB copper. I could get them to work mostly using an emery board to sand off that oxidation but I still don't trust them.

    Anyway, I measured the current of the OEM bulbs

    5 bulbs with the blue support inside are 250 ma. at 12.50 volts
    9 bulbs with the white support inside are 175 ma. at 12.50 volts
    1 bulb with the blue support inside is 74 ma.

    Not sure if that one bulb is just bad or it's the one going to the alternator lamp.

    My 5 new white LEDs are switching regulator type and draw 60 ma. each at 12.50 volts. It draws 54 ma. at 14.5 volts. Note these LEDs have the wire wrapped around the bottom so the wire is on both sides. That gives me a lot of wire to solder to the PCB.

    The colored indicator LEDs draw 15 ma. at 12.50 volts. They are pretty bright. I may be able to pull those LEDs out of the case and drop the current (for the green LEDs). These have the wire on one side so may not be enough to solder those.

    You really need the sockets to hold the PCB down and hold the LED straight in the fixture. Also these OEM sockets are made for the thicker plastic and have the taps placed at
    the correct angle for the PCB contact. Not sure if you can buy new sockets that would work.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  4. #9544
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    I was able to pull the green LED circuit board out by just unbending the wires. It has a 200 ohm resistor to limit the current. I played with adjusting that resistor and decided it should be a 1.0 Kohm. That brings the current down from 19.9 ma to 4.8 ma which I think will not be to bright for the turn signals and low beam lights. I have to think about the other colors. Probably the high beam light is also to bright but the red lamps you would want bright for your attention.

    Anyway those resistors are 0603 size components and I don't have those in my parts or junk box. I will have to order some.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  5. #9545
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    I was wrong on the resistor size. They are 0805 which I use almost exclusively. The blue uses a 200 ohm, the red a 390 ohm and the amber a 390 ohm. I tested them all with 1.00 Kohm and they all look around 5 or 6 ma. So that is what I'm going to use on all the indicator bulbs. The alternator remains the incandescent bulb.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  6. #9546
    Senior Member
    Join Date:  Dec 2018

    Posts:    1,544

    Would be nice if you could take a pic before and after in the same lighting conditions.

  7. #9547
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    Quote Originally Posted by Helirich View Post
    Would be nice if you could take a pic before and after in the same lighting conditions.
    I don't think I would want to put the bulbs back in for a photo. It was completely stock. I'm thinking the 5 illumination LEDs are going to be to bright. Not sure if PWM can dim those switching regulator LEDs so I may have to change those. It's not much work to change the resistors in the indicator LEDs. I'm also replacing the wire for more length so I can solder those to the PCB copper.
    Last edited by Bitsyncmaster; 11-14-2026 at 08:41 PM.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  8. #9548
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    Quote Originally Posted by Bitsyncmaster View Post
    I don't think I would want to put the bulbs back in for a photo. It was completely stock. I'm thinking the 5 illumination LEDs are going to be to bright. Not sure if PWM can dim those switching regulator LEDs so I may have to change those. It's not much work to change the resistors in the indicator LEDs. I'm also replacing the wire for more length so I can solder those to the PCB copper.
    I tested those illumination bulbs with PWM and I can dim them. I hope to have all the LEDs soldered in today. Looking forward to another project making the PWM driver. I get bored just building inventory.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  9. #9549
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    Finished the LEDs and installed the binnacle. Illumination lights look nice. Will have to drive it at night to see if they are to bright. Looks like all indicator lights are working.

    My blinkers are not working (nothing either direction) but the 4 way flashers work. This shows me those blinker indicators are working.

    My fuel gauge is pointing 6:00. I think it did work before I started the car.

    So I have to fix those two problems before I bolt the binnacle down.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  10. #9550
    Senior Member
    Join Date:  Nov 2022

    Posts:    148

    My VIN:    7012

    Fuel gauge at 6:00 seems to most commonly be due to the needle getting stuck. On my car it seems to happen when I'm at 1/2 tank or less. I can tap on the binnacle a bit to jostle it back to being driven by the electrical signal, but as soon as I shut off the car and turn it back on again, it will go back to being stuck at 6:00. If I stay above 1/2 tank, it doesn't get stuck.

    I'm planning to install pin stop on the gauge this winter, unless I open it up and see some obvious gunk that I can clear off to fix it.

Page 955 of 956 FirstFirst ... 455 855 905 945 953 954 955 956 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •