FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 22 of 22 FirstFirst ... 12 20 21 22
Results 211 to 220 of 220

Thread: Backlit Electronic Instrument Cluster

  1. #211
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    I finally did it!
    15 years later I finally did it.

    Its a rough prototype, but it works.
    A LOT more refinement and revisions yet to do.
    Car is still stuck in the garage as I damaged the tie rod trying to remove it when replacing the angle drive with an electronic sensor, so no road tests for about a week.
    Enjoy this video preview I took last night when I connected the prototype into the car for the first time last night.

    Jim Reeve
    DMC6960

  2. #212
    Senior Member DMC5180's Avatar
    Join Date:  May 2011

    Location:  Reedsburg, WI

    Posts:    4,042

    My VIN:    5180

    Club(s):   (DMWC) (DCUK)

    Nicely done. Are you still using the AD? Did you find an off the shelf sensor or did you need to create one?


    Sent from my iPhone using Tapatalk
    DENNIS

    VIN 5180, Frame 3652, STAGE II​, EPS​, DM-eng Solid State Solutions (RPM Rly, Dm.Lt.Mod., Fan Fail Mod. , FAN Rly, HS.Rly) , HID headlights, SPAX user since 2009, Eibach springs, M Adj. Rear LCA's, DPNW poly-sway bar kit, DMCEU LCA Stabilizer link kit, DMCMW Illuminated door sills, Aussie Illuminated SS Shifter plate, REAL MOMO EVO Steering wheel, DELOREANA Extended View Side Mirrors w/ Heaters, DELOREANA LED Door Lights.

  3. #213
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Quote Originally Posted by DMC5180 View Post
    Nicely done. Are you still using the AD? Did you find an off the shelf sensor or did you need to create one?
    To specifically answer the angle drive question - It was completely replaced with a variable reluctor speed sensor.

    This is another rough aspect of the first prototype. I had originally hoped to simply thread the inside of the hub nut, but there were multiple problems with that. For one, there was no clearance to screw on the speed sensor to the hub nut after it was installed. The spring is way too close. Second problem, the length of the threaded section on the speed sensor was way too long to seat nicely into it even if I got around the spring clearance problem.

    The solution for now, I stripped off the threads on the speed sensor and cut off almost a 1/2" of the end of it. It is still fully functional. I didn't have a positive way to secure it, so its currently held in with a combination of locktite, sillicone, duct tape, and zip ties. I disassembled another speed sensor to see how its designed. Its pretty simple so I think making a custom housing or having a professional machine shop machine the existing housing is a high probability. Next iteration will properly snap into the hub nut just like the angle drive.

    A few photos showing the speed sensors, the modification (butchering?), and the rough installation.

    Sensor almost fitting into hub nut, needs to go in a little further...
    IMG_5065.jpg

    From the inside of the nut, sticks in too far, needs to be cut down...
    IMG_5067.jpg

    Dry fit...
    IMG_5084.jpg

    Works for now, we'll see for how long...
    IMG_5088.jpg

    Sensor uses a smaller square key than the dustcap. Hollow brass rod for the quick adaptor...
    IMG_5089.jpg

    Just needed another quick trim to get the exact length needed and also providing a small amount of thermal expansion room...
    IMG_5090.jpg

    And the sensor itself, shave some threads and lop off the end...
    IMG_5064.jpg

    The inner workings of the sensor, not easly to take apart (crimped aluminum), but simple enough once inside...
    IMG_5079.jpg
    Jim Reeve
    DMC6960

  4. #214
    Senior Member - Owner since 2003 Patrick C's Avatar
    Join Date:  May 2011

    Location:  Northern Michigan

    Posts:    1,237

    My VIN:    1880

    Club(s):   (DCO) (DCUK)

    Quote Originally Posted by dmc6960 View Post
    I finally did it!
    15 years later I finally did it.

    Its a rough prototype, but it works.
    A LOT more refinement and revisions yet to do.
    Car is still stuck in the garage as I damaged the tie rod trying to remove it when replacing the angle drive with an electronic sensor, so no road tests for about a week.
    Enjoy this video preview I took last night when I connected the prototype into the car for the first time last night.

    Amazing job, Jim!
    Patrick C.
    VIN 1880

  5. #215
    Motors about after dark Michael's Avatar
    Join Date:  May 2011

    Posts:    4,922

    My VIN:    Banged your VIN'S mom

    I need this more than anyone else ever needed anything in the history of man.
    http://dmctalk.org/image.php?type=sigpic&userid=90&dateline=161808992  9

  6. #216
    Member
    Join Date:  Sep 2021

    Location:  London, Ontario, Canada

    Posts:    48

    My VIN:    5637

    Any reason not to just use a tone ring on the axle instead of having to deal with the pain in the butt factor of adapting the angle drive shaft/nut to the speed sensor?

    From someone who has made an electronic gauge cluster to another, there are few in the world who know how much of a monumental time suck it really is.

  7. #217
    Senior Member AugustneverEnds's Avatar
    Join Date:  Jul 2012

    Location:  Syracuse, NY area

    Posts:    1,059

    My VIN:    10287

    Club(s):   (DMA)

    A worthy upgrade! Very cool sir.
    Nick A.

    1988 BMW 325is
    1982 DeLorean DMC-12
    1989 Jaguar XJ6

  8. #218
    '82 T3 FABombjoy's Avatar
    Join Date:  May 2011

    Location:  Lansing, MI

    Posts:    1,227

    My VIN:    10270

    Quote Originally Posted by Aaron Cake View Post
    Any reason not to just use a tone ring on the axle
    This works very well. Off the shelf Porsche 930 encoder rings fit. If you cut the ring in half, you don't need to remove or disassemble the axle.
    Luke S :: 10270 :: 82 Grey :: Supercharged K24 / G96 Swap (in progress)

  9. #219
    Member
    Join Date:  Feb 2015

    Location:  Allen, TX

    Posts:    79

    My VIN:    #4595

    Incredible job! Absolutely love it.

  10. #220
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Prototype Update

    Thought I'd give an end-of-season update on the prototype I finished this spring.

    All-in-all, I put a bit over 2300 miles on the car. The AC is currently not working, so didn't drive it much during the hottest summer months. Then I also lost my heater core, so I haven't been driving it much in the cooler weather either. Just can't win sometimes.

    What worked well -

    The backlighting! This is incredible how much more finished it makes the cluster appear. The speedometer has been the next best thing, after going for a decade without a working speedometer I now have a rock solid pointer (no bouncing!) and built it with a 140mph face to match the few cars that got a factory 140mph unit. The OLED display in place of the trip-meter has been great for not only displaying the odometer and trip meter(s), but also every other digital sensor reading that comes to the instrument cluster. There were no so software failures during operation, longest single drive between ignition cycles was probably about 2 hours, so no full fuel tank draining drive tests, but still a good workout. It has had cold operation, and hot operation, and performed well despite not all components being automotive rated yet.

    What needs improvement -

    I built this as a rough prototype, knowing I would need several iterations before perfecting it. Now that I've had plenty of time with version 1, I can iterate and build a 2nd version. Things that need changing are as follows...

    • OLED display location. The display in place of the trip meter, is the exact size and location of the stock trip meter on the speedometer. Unfortunately, its location leaves the display partially obscured by the tail of the pointer when the speedometer is at speed. I'll need to lower its location by a bit for the next version.
    • Stepper motor failure. I had one of the stepper motors which drive the pointers fail. This is entirely my fault though, as I had been reusing the same ones over several pre-prototype builds. It was just too much for it to handle. I'll be sure to only use brand-new stepper motors for the next build.
    • Tachometer. I built this version using a lot of pre-built modules I was able source off the internet. In the interest of proving the concept of operation more than full integrated hardware, this simplified the build quite a bit. Unfortunately I wasn't able to get the optoisolator board to work for the tachometer. An optoisolator is a component that air-gaps the electrical signal coming from the ignition coil so the extreme voltage surges do not fry the microcontrollers. I built a second one by hand using the same circuit my Megasquirt has used successfully for 16 years now. That gave me a working tach for about 50 miles before something on that failed as well, which I'm suspecting is just a poor solder joint or other loose connection. During those 50 miles, it worked great so I know the code is generally sound.
    • Light bleed. This version used a piece of clear acrylic between the front PCB and the gauge decals. I painted over the opaque areas with black paint, but it wasn't quite enough and ended up with a lot of light bleed between the gauges, and around the perimeter as well. Future versions will use black ABS as the front with cutouts only where the light needs to pass.
    • Needle illumination. The lights I used to illuminate the needles were too dim. This is a simple one though, I just need to change the load resistor for those LEDs to and brighten them up a bit. I went a little too high on them.
    • Speed sensor. As I previously posted the details about installing the speed sensor in place of the angle drive, I need to improve on how it is mounted in the car. I haven't had any issues with how I did it, its worked perfectly so far. I just can't forget that it does need much improvement.


    I still need to do a write-up about the build process for this prototype in the first place. I'll get to that maybe in the next few days. Until then, if you want to see a live demo of the dash in action, here is an 18 minute overview video I made that goes over everything.
    Enjoy...

    Jim Reeve
    DMC6960

Page 22 of 22 FirstFirst ... 12 20 21 22

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •