FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 956 of 956 FirstFirst ... 456 856 906 946 954 955 956
Results 9,551 to 9,553 of 9553

Thread: What have you done to your DeLorean today?

  1. #9551
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    I'm now guessing the problem with my blinkers is the flasher relay. I did not think of this before but the indicator lamps were incandescent and now just draw 5 ma. I had bought an LED flasher back when I put LEDs in the front and back signals. But it may not be good enough now there are no incandescent bulbs. It must be right on the edge of working because the 4 way flashers work which puts more LED loads on it. I was looking for an incandescent bulb to test this theory but could not find one in my junk draws.

    I'll just buy another flasher.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  2. #9552
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    Quote Originally Posted by mike123 View Post
    Fuel gauge at 6:00 seems to most commonly be due to the needle getting stuck. On my car it seems to happen when I'm at 1/2 tank or less. I can tap on the binnacle a bit to jostle it back to being driven by the electrical signal, but as soon as I shut off the car and turn it back on again, it will go back to being stuck at 6:00. If I stay above 1/2 tank, it doesn't get stuck.

    I'm planning to install pin stop on the gauge this winter, unless I open it up and see some obvious gunk that I can clear off to fix it.
    You are correct. It was just stuck (does need stops). What I did was pull out the binnacle and put 12 volts on the power pin and the gauge did not move (It should show 12:00) with power and no sensor load). I had to bang on the binnacle pretty hard to get it to fly to 12:00. I put the binnacle back in the car and now the gauge is working. So I guess my gauge does not get stuck at 12:00.

    I really should put a pin stop on it now that the binnacle is out, but I'm getting tired of working on it.

    If your gauge gets stuck at 6:00 it may help to open the sensor connection and then the voltage is working with more force on the gauge.
    Last edited by Bitsyncmaster; Yesterday at 10:49 AM.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  3. #9553
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    Quote Originally Posted by mike123 View Post
    Fuel gauge at 6:00 seems to most commonly be due to the needle getting stuck. On my car it seems to happen when I'm at 1/2 tank or less. I can tap on the binnacle a bit to jostle it back to being driven by the electrical signal, but as soon as I shut off the car and turn it back on again, it will go back to being stuck at 6:00. If I stay above 1/2 tank, it doesn't get stuck.

    I'm planning to install pin stop on the gauge this winter, unless I open it up and see some obvious gunk that I can clear off to fix it.
    I'm guessing your running the OEM sender because that would drive both fuel gauge coils at the same time on key on. If you have a capacitor on your sender that would be worse.
    Dave M vin 03572
    http://dm-eng.weebly.com/

Page 956 of 956 FirstFirst ... 456 856 906 946 954 955 956

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •