FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 7 of 22 FirstFirst ... 5 6 7 8 9 17 ... LastLast
Results 61 to 70 of 220

Thread: Backlit Electronic Instrument Cluster

  1. #61
    Senior Member DMC5180's Avatar
    Join Date:  May 2011

    Location:  Reedsburg, WI

    Posts:    4,042

    My VIN:    5180

    Club(s):   (DMWC) (DCUK)

    Jim,

    Have you contacted any of the Driver chip suppliers to see if you can get developmental "Samples". Usually "off the shelf" component suppliers will work with you even if your only a small fish. Was there anything available at Digikey,Newark,Allied or Mouser?
    DENNIS

    VIN 5180, Frame 3652, STAGE II​, EPS​, DM-eng Solid State Solutions (RPM Rly, Dm.Lt.Mod., Fan Fail Mod. , FAN Rly, HS.Rly) , HID headlights, SPAX user since 2009, Eibach springs, M Adj. Rear LCA's, DPNW poly-sway bar kit, DMCEU LCA Stabilizer link kit, DMCMW Illuminated door sills, Aussie Illuminated SS Shifter plate, REAL MOMO EVO Steering wheel, DELOREANA Extended View Side Mirrors w/ Heaters, DELOREANA LED Door Lights.

  2. #62
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Quote Originally Posted by DMC5180 View Post
    Have you contacted any of the Driver chip suppliers to see if you can get developmental "Samples". Usually "off the shelf" component suppliers will work with you even if your only a small fish. Was there anything available at Digikey,Newark,Allied or Mouser?
    This is a very specific type of driver chip, probably very uncommon with hobbyists. None of the common major electronics distributors have anything even close. I've contacted MCR and Juken Swiss Technology about samples. MCR said no, minimum order is 100 at $6.50 each; and there was no response from Juken.

    In other news, after this weekend's foray in my first extended go with PIC programming....
    Jim Reeve
    DMC6960

  3. #63
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Working Stepper Motor for Gauge Needles

    I now have a basic control of the stepper motor destined to drive the needles for the gauges...



    This is running a preset program which is turning it 300ยบ in each direction, with a 1 second pause between each rotation.

    Next step is to control its movement and position with a potentiometer. This will simulate the oil pressure, engine temp, and fuel level senders; and provide complete proof-of-concept with everything I need to do. If I am successful in doing this, I will likely not even need the dedicated driver chips I talked about earlier.

    Progress is here.
    Jim Reeve
    DMC6960

  4. #64
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    Looks good. Even looks fast enought to use for the tach. Another guy getting into software to replace our 70's hardware
    Dave M vin 03572
    http://dm-eng.weebly.com/

  5. #65
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    And it should be able to go at least twice as fast as this, with proper acceleration curves built into the program. (That part is still beyond what I've accomplished). This seems to be the fastest it can go reliably without missing a step.

    To finish my next goal, I need to divide an 8 or 10 bit ADC code into the number 150 or less, then write some if/thens to add/subtract X (the difference between Y [the current position of the stepper] and Z [the ADC code, the desired value of Y]), to/from Y.

    My first attempt at reading how to do this (the chip doesn't actually divide) had my head spinning faster than that motor. My first reads on the if/thens were at least mostly comprehended.
    Jim Reeve
    DMC6960

  6. #66
    Senior Member robvanderveer's Avatar
    Join Date:  May 2011

    Location:  Netherlands

    Posts:    612

    My VIN:    3695

    Club(s):   (DCN)

    To get your prototype working, i suggest you use a higher level cpu/platform to experiment with the hardware. I've had amazing experiences with Netduino or TinyClr, both C#, .Net capable, step through debugging, full programming support. Their prototype boards are about the size of a deck of cards.

  7. #67
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,633

    My VIN:    03572

    Just shift the 8 bit value to the right one place to divide by 2. Hence you will get a number from 0 to 127.

    For 10 bit shift it 3 times for the same 0 to 127 number.

    That is how you divide in assembler code with simple CPUs.. To divide by other exponents, you can manipulate a few shifts and add the two values.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  8. #68
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Quote Originally Posted by robvanderveer View Post
    To get your prototype working, i suggest you use a higher level cpu/platform to experiment with the hardware. I've had amazing experiences with Netduino or TinyClr, both C#, .Net capable, step through debugging, full programming support. Their prototype boards are about the size of a deck of cards.
    Thats a bit more complex than I need for this project. I should be able to control both the Volt/Temp gauge with a single PIC16 chip, both the Oil/Fuel gauge with a single PIC16 chip, the Tach with a single PIC16 or 18 chip, and the Speedo likely a single PIC18 chip.

    This whole project is a start-from-scratch learning for me. Too easy to go over my head so I'm keeping each step very simple. Starting with the simple gauges then working my way up.
    Jim Reeve
    DMC6960

  9. #69
    EFI DeLorean dmc6960's Avatar
    Join Date:  May 2011

    Location:  Minnesota

    Posts:    1,591

    My VIN:    06960

    Another General Update

    Ordered 6 .30" 7-segment green LED displays for experimental use for the odometer. A Vacuum florescent display is going to be DOA, as there are no commercially available ones in the package/size I need. Not to mention that in general the LED displays are several times cheaper AND have the ability to be built in different colors. There are .28" ones available as well, but I'm going to try the .30" ones first. FYI the vertical opening on the speedometer for the odo display is .28".

    Color update - Backlighting WILL be available in 3 colors; Green, Red, and Blue. These are the most commonly requested colors. Green backlit will have alternate colors for all the alternately colored labels (red, yellow, and blue). The red and blue backlighting will wait and see how it looks before determining those other colors. Odometer colors will be green (normal), with red and blue optionally. If it is ever desired to switch colors of the backlight (like a person's different preference if the car is sold), the unit can be returned and colors switched for a small fee. Unfortunately RGB 7-segment displays are not available in the extreme small size needed, thus a user-adjustable color can not be an option.

    After this project is done (at least a year from now) I may consider building a replacement A/C decal in the unavailable most-desired style (Type 2 or 3 here), LED backlit, which will have the option to plug-in to the new cluster for matched dimming. Color options will be the same as the cluster.
    Jim Reeve
    DMC6960

  10. #70
    Senior Member robvanderveer's Avatar
    Join Date:  May 2011

    Location:  Netherlands

    Posts:    612

    My VIN:    3695

    Club(s):   (DCN)

    For proper 'old school' display, this would be way cool:


Page 7 of 22 FirstFirst ... 5 6 7 8 9 17 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •