Location: Baton Rouge, Louisiana
Posts: 3,047
My VIN: 16510 and carbureted
Club(s): (GCD) (SEDOC) (DCUK)
Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
Not at the rate I am working...
This is the first I have heard of Bill threatening, um I mean offering to come down. ;D
Bear in mind that on top of the damage I found to the interior, I still have no a/c -- it was 87 degrees during winter here so you can guarantee we will be driving to Orlando in record heat. I also haven't figured out why the cruise control doesn't work. A ten-hour drive with no cruise control is murder on my right leg. And I haven't even fixed the vacuum leak yet.
I think my car might scare Bill away...
Now I have to save up money for new carpet. I can survive on ham sandwiches and lemonade, but my girlfriend is used to a higher gustatory standard... saving that kind of money between now and June will be difficult... or I could just drive without carpets.![]()
3.0L, automatic, carbureted
Location: Baton Rouge, Louisiana
Posts: 3,047
My VIN: 16510 and carbureted
Club(s): (GCD) (SEDOC) (DCUK)
Location: Baton Rouge, Louisiana
Posts: 3,047
My VIN: 16510 and carbureted
Club(s): (GCD) (SEDOC) (DCUK)
Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
Okay, so this is interesting...
When I took the seats out, I noticed that there appear to be thick washers adhered to the driver seats but not the passenger seat.
Lo and behold -- someone installed all eight washers on one seat.
SANY0084.jpg
And of course they're all stuck together.
This car just gets more and more interesting!
One more question: these are body bolts, right? Can I assume that they connect with the frame?
bodybolts.jpg
If so, then they are ground points. I may not be running a ground bus like Bill, but if these are good grounds, then I think I may have found a place to ground my inertia switch!
3.0L, automatic, carbureted
Location: Dahlonega GA
Posts: 2,462
Club(s): (SEDOC) (DCUK)
eBay selling at it's best I can tell you stock Delorians and quite a bit of slugs so the Turbo is a super nice up-grade.
K-Jet: Causing electrical issues since November 5th 1955
Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
Thanks. That reminds me, I need to order some M10x1.5 bolts and square washers to replace the body bolts in the engine compartment. I am adding them to my McMaster order...
Oh, and I checked out what O'Reilly had listed as an output flange seal. National Part #1962. $4.06 including tax.
SANY0089.jpg
SANY0090.jpg
SANY0092.jpg
SANY0093.jpg
Looks like OEM to me.
3.0L, automatic, carbureted
Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
McMaster order placed:
- Black #6 sheet metal screws and finishing washers to replace all of the oddball, "make it fit" ones in the interior of the car.
- Stainless M8 lock-nuts to replace the rusted original lock-nuts under the seats.
- Nylon M8 washers for the lock-nuts above.
- ΒΌ"-20 jack-nuts, enough to replace all of the ones in my rear fascia (installation tool included).
- Stainless hardware for the license plate surround and taillight lenses.
- New large washers for the seats.
- New M10x1.5 body bolts and captive nuts for the engine compartment.
Time for a ham sandwich and glass of lemonade.
Last edited by Farrar; 03-04-2012 at 10:09 PM.
3.0L, automatic, carbureted