FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 77 of 111 FirstFirst ... 27 67 75 76 77 78 79 87 ... LastLast
Results 761 to 770 of 1102

Thread: Farrar's car blog

  1. #761
    Not dead yet, also Admin. sean's Avatar
    Join Date:  May 2011

    Location:  Dahlonega GA

    Posts:    2,462

    Club(s):   (SEDOC) (DCUK)

    Quote Originally Posted by Farrar View Post
    What about buying a sheet of 1/2" fiberglass and cutting it to fit? Can you cut fiberglass with a jigsaw or saber saw? Would the edges need to be re-epoxied for strength?
    I didnt know you could by sheets of 1/2" fiberglass. It would probably take a special blade for your jig saw to cut it and of course wear a mask. Sanding the cuts is probably all you would need to do afterward but again, I didnt know you could get 1/2" fiberglass sheets.

    Quote Originally Posted by Farrar View Post
    No, but I could use Lexan and be able to see the mice building nests in the car...

    Farrar
    Not if its covered in sound proofing.
    eBay selling at it's best I can tell you stock Delorians and quite a bit of slugs so the Turbo is a super nice up-grade.
    K-Jet: Causing electrical issues since November 5th 1955

  2. #762
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by sean View Post
    I didnt know you could by sheets of 1/2" fiberglass.
    You can, but they're expensive!!!


    Quote Originally Posted by sean View Post
    Not if its covered in sound proofing.
    Ah, you saw through my joke. Damn.

    Seriously, though, that brings up a point -- I bet plywood is better at dampening sound than any kind of plastic or fiberglass.

    I might just see what kind of wiggle room I have behind the 1/2" plywood panels. If I have 1/2", then that's enough for some serious soundproofing, weight gain be damned.
    3.0L, automatic, carbureted

  3. #763
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by Farrar View Post
    weight gain be damned.
    People always amuse me when they talk about making modifications to their cars to decrease vehicle weight. People never seem to consider just loosing 20 or 30 pounds off of the driver.

  4. #764
    Not dead yet, also Admin. sean's Avatar
    Join Date:  May 2011

    Location:  Dahlonega GA

    Posts:    2,462

    Club(s):   (SEDOC) (DCUK)

    Quote Originally Posted by stevedmc View Post
    Have you considered using transparent aluminum?
    Pfft, that's so 1986


    Quote Originally Posted by stevedmc View Post
    People never seem to consider just loosing 20 or 30 pounds off of the driver.
    BURN!!! Farrar just got Riced!
    eBay selling at it's best I can tell you stock Delorians and quite a bit of slugs so the Turbo is a super nice up-grade.
    K-Jet: Causing electrical issues since November 5th 1955

  5. #765
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by stevedmc View Post
    People always amuse me when they talk about making modifications to their cars to decrease vehicle weight. People never seem to consider just loosing 20 or 30 pounds off of the driver.
    Over the past year, I have been trying to make my car faster by losing weight. Unfortunately, I am thinner but heavier than I was six months ago. Muscle is denser than fat. I have yet to reach the point where I am losing size AND weight -- it's a long process. But look at it this way: if I am lighter and so is the car, that's a win-win, right?

    P.S.: Carrying 100+ pounds of tools in the trunk doesn't help the car be faster, either, but it does help make it more reliable.
    3.0L, automatic, carbureted

  6. #766
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by Farrar View Post
    Over the past year, I have been trying to make my car faster by losing weight. Unfortunately, I am thinner but heavier than I was six months ago.
    You look like you have been losing weight to me. I'm not one to compliment another man's appearance but yeah, Farrar doesn't look as big to me as he was a year ago.

  7. #767
    Not dead yet, also Admin. sean's Avatar
    Join Date:  May 2011

    Location:  Dahlonega GA

    Posts:    2,462

    Club(s):   (SEDOC) (DCUK)

    Quote Originally Posted by Farrar View Post
    P.S.: Carrying 100+ pounds of tools in the trunk doesn't help the car be faster, either, but it does help make it more reliable.
    Double edged sword right there...
    eBay selling at it's best I can tell you stock Delorians and quite a bit of slugs so the Turbo is a super nice up-grade.
    K-Jet: Causing electrical issues since November 5th 1955

  8. #768
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by stevedmc View Post
    Farrar doesn't look as big to me as he was a year ago.
    I'm not as big, but I am heavier. It's weird. Back then I weighed 205. Now my pants are two inches slimmer and I weigh 225! That is proof that I am gaining muscle, but that I still have more fat to lose. I am doing it the slow way: instead of working out really hard at the gym and going on a crash diet, I am simply eating healthier and going on long walks. I figure it's better for my long-term health. Plus walking around the neighborhood at a brisk pace is free. Gym memberships are expensive.

    Back on topic: my McMaster order arrived a few minutes ago! Exciting times.

    Quote Originally Posted by sean View Post
    Double edged sword right there...
    True. And actually, I only carry my electrical kit, spare belts, and a few metric wrenches with me. It's just these days with the car not going anywhere except for short test drives, I might as well just leave the toolboxes in it.

    Well, it looks like I wasted a few bucks. Not the first time with this car, of course. But anyway, check this out. The screw and washer on the left came out of the car. The screw and washer on the right are -- or were going to be -- their McMaster replacements. (Of six such screws in the interior of the car -- two holding down the shifter plate, and four holding down the glove box, this is the only one which looks original.) The stock screw is definitely too small to be #8 size, but the screw on the right is #6 and it's obviously smaller. Is there an elusive #7 size for sheet metal screws out there somewhere, or is this some metric-sized sheet metal screw I've never heard of before?

    SANY0095.jpg

    But at least I did have some success. Check out the replacement for the missing rear body bolt, compared with the original on the left:

    SANY0096.jpg

    I think that will do the trick! BTW, "safety blue" was cheaper, and since it's in the pontoon no one will ever see it anyway. I wanted to spring for stainless. Maybe some day.

    And while we're at it, say hello to my new license plate bracket mounts, pre-installation:

    SANY0097.jpg

    The jack nuts came with an "installation tool," but it's what you would expect for free: a piece of crap. My "installation tool" will be a much longer Allen-head screw and a spacer. Fortunately these are SAE sized so I can get those at my local Ace Hardware.

    But back to the sheet metal screws, the ones that go into the speed-nuts -- are they metric? Or size #7 that I've never heard about? I feel silly now -- I have 50 each of the screws and countersunk washers. Maybe I will just buy smaller speed-nuts!
    3.0L, automatic, carbureted

  9. #769
    My friends think I'm nuts jawn101's Avatar
    Join Date:  May 2011

    Location:  Sacramento-ish

    Posts:    4,408

    My VIN:    02100

    Club(s):   (NCDMC) (DCUK)

    Quote Originally Posted by Farrar View Post
    The jack nuts came with an "installation tool," but it's what you would expect for free: a piece of crap. My "installation tool" will be a much longer Allen-head screw and a spacer. Fortunately these are SAE sized so I can get those at my local Ace Hardware.
    If the tool you got is the little metal shim with a hole at either end, it works surprisingly well... you don't need much more than that
    Jon
    1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
    restoration log, March 2011 to present
    full and detailed photo restoration log

  10. #770
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by jawn101 View Post
    If the tool you got is the little metal shim with a hole at either end, it works surprisingly well... you don't need much more than that
    Really? Okay, it looks pretty flimsy to me, but I might as well give it a try! Thanks.
    3.0L, automatic, carbureted

Page 77 of 111 FirstFirst ... 27 67 75 76 77 78 79 87 ... LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •