Nice job on this Jim. Looking forward to seeing more.
Location: Peoria, AZ
Posts: 72
My VIN: SCEDT26TXBD001292 SCEDT26T6DD020098
Club(s): (AZ-D) (DMA) (LINY-DMC) (DCUK)
Nice job on this Jim. Looking forward to seeing more.
- Josh
SCEDT26TXBD001292: Black 5 spd - Holley EFI 3.0L PRV - Custom TwinTurbo by DeLorean Industries
************************************************** ***********************
SCEDT26T6DD020098: Grey 5 spd - K-Jet CIS 2.85L PRV
Totally awesome!
Andy Lien
VIN 11596 Jan 1982 build - owned since Nov. 2000!
Total frame-off restoration completed 2021-2023
Photography and Backpacking is life.
Was Fargo, ND
Now Kansas City
Location: Sacramento-ish
Posts: 4,408
My VIN: 02100
Club(s): (NCDMC) (DCUK)
Jim, these are so awesome... do you have any plans to offer an overlay to let the folks who stay with their stock gauges revitalize the faces? I bet you could sell the pants off that and it might help defray some of your costs in developing the electronic cluster. Just a thought, I have no idea what any of the economics of your project are.![]()
Jon
1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
restoration log, March 2011 to present
full and detailed photo restoration log
Unfortunately no, this will not be a possibility. You would have to do all of the gauge faces to match, and there are going to be enough subtle differences that the new faces will not be 100% compatible with the original gauges. One example is the speedometer. If you see my previous notes you'll notice the stock gauge has a 2º counter-clockwise bias in all the ticks. The spacing isn't 100% equal either. Those deficiencies needed to be corrected for the electronic speedo and as such could not accurately be used on an original speedometer.
Jim Reeve
DMC6960
Location: Peoria, AZ
Posts: 72
My VIN: SCEDT26TXBD001292 SCEDT26T6DD020098
Club(s): (AZ-D) (DMA) (LINY-DMC) (DCUK)
I noticed that these two MPH gauges looked different. When it's said that no two DeLorean's are the same, it makes sense.
[ATTACH=CONFIG]10411[ATTACH=CONFIG]10412
These two pics are from the cars DMC Florida currently has up on eBay.
- Josh
SCEDT26TXBD001292: Black 5 spd - Holley EFI 3.0L PRV - Custom TwinTurbo by DeLorean Industries
************************************************** ***********************
SCEDT26T6DD020098: Grey 5 spd - K-Jet CIS 2.85L PRV
Location: Sacramento-ish
Posts: 4,408
My VIN: 02100
Club(s): (NCDMC) (DCUK)
Jon
1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
restoration log, March 2011 to present
full and detailed photo restoration log
Unfortunately, I was unable to get decals printed out in time to bring to the show. This pretty much means there is nothing to show people at DCS. I'm a bit disappointed, but oh well. By the time for the next show I hope to have a vendor booth and be selling them like hotcakes! Now that the majority of the work I needed to do on my own car is complete, I can continue work on this sometime after returning from DCS.
Jim Reeve
DMC6960
Whats new? :-)
Billy C. VIN: 2964
"Trying to Live the Dream!"
"If you're gonna own a DeLorean, why not build it with some style?"
http://www.facebook.com/billy.chingas.7
Ha, had a feeling you'd ask.
Haven't worked too much on it since our last PMs. For everyone else, here is the general update from over the summer...
I wasn't able to get any prototype decals printed up in time for DCS. Since there hasn't been any other pressing need for something good looking and flashy, I haven't pursued that any further yet. For operational prototype purposes I can use cheaply printed decals. I've also inquired about the engineering diagrams for the original cluster if found. I HAVE found out the technical name for the typeface used in the cluster. All characters match except the zero/"O". I may yet end up redrawing the whole cluster, especially if I get the engineering drawings. That'll be easy though, and can wait until later since what I have now will be more than good enough for operational prototypes.
I've done a little more work on the software I have controlling the stepper motors. I've also got an analog circuit ready to test the real DMC sensors in the program. Still need to build a basic power supply for the testing. I have not yet started on the software that operates all the other functions of the cluster, like the PWM dimming of the backlighting, high temp triggers, etc. I'm also reading up on the more complex uC's I'm going to need for the speedometer, which is by far the most complex gauge and will likely be my last to complete.
I've done some rough work on 3D renderings of the cluster housing and gauge faces with the hope that a design of my own will reduce development costs. The housing may still be something I make myself, but the gauge face(s) certainly need to be a professionally molded product. So far though I haven't been very good at 3D rendering, curious what tools other folks use.
So thats about it for now, I did spend much of the summer just driving my car and doing home maintenance. I should have relatively large amounts of free time this winter, especially after the new year to work on this. I've gone 3 years now without a reliably working speedometer, I'm motivated.
Jim Reeve
DMC6960