Steve Rice needs to mentally add 150 miles driven with a rounded out dust cap to his odometer reading.
Location: Baton Rouge, Louisiana
Posts: 3,047
My VIN: 16510 and carbureted
Club(s): (GCD) (SEDOC) (DCUK)
Steve Rice needs to mentally add 150 miles driven with a rounded out dust cap to his odometer reading.
Use a drill motor...
Location: Baton Rouge, Louisiana
Posts: 3,047
My VIN: 16510 and carbureted
Club(s): (GCD) (SEDOC) (DCUK)
Unwinds the spindle cable (too many RPM's).
Use a variable speed drill motor...
Location: Baton Rouge, Louisiana
Posts: 3,047
My VIN: 16510 and carbureted
Club(s): (GCD) (SEDOC) (DCUK)
Or just don't care. There are plenty of Deloreans out there that don't have working speedometers anyway.
On another note, my speedometer finally started acting up again. For a few miles it started bouncing around and then started working perfectly again. This was about 200 to 300 miles ago. My guess is those plastic dust caps get tired of turning a piece of metal after 3 or 4 hours of nearly non-stop driving. Plastic becomes soft when it gets hot and I can imagine there is a lot of friction going on where the metal cable goes into the plastic cap.
When I installed the new dust cap I could tell the angle drive cable was a little loose, but at the time it was able to stay in there without stripping anything. When I get home, I am going to take the angle drive cable and JB Weld it into the cap. Right now I'm in West Memphis and have no desire to go searching for a Walmart and Jack the car up. As of right now the speedometer is working fine but I wouldn't be surprised if it started acting up again tomorrow.
Location: Baton Rouge, Louisiana
Posts: 3,047
My VIN: 16510 and carbureted
Club(s): (GCD) (SEDOC) (DCUK)
Bill Robertson has a JB Welded dust cap. He made it by inserting a piece of smooth sided 1/8" square brass tube from a hobby shop into the JB Weld while it was wet, then pulling it out when the JB Weld had dried. It's a very snug fit on the spindle cable, but there is now absolutely no slop between his spindle cable and his dust cap whatsoever.
Location: Lexington, NC
Posts: 817
My VIN: #5000 (Grey, manual, SS chassis, intercooled twin turbo), #16128 (Grey, auto, efi twin turbo), #888
Club(s): (DCVA) (SEDOC) (DCUK)
I'm glad you are making these posts about your intermittent angle drive. I too am having intermittent failures and I had convinced myself it was the dust cap only. I talked with another owner at the tech session and he said his AD was culprit from intermittent failure. My only other experience with AD failure was sudden and permanent. I was supposed to get a dust cap from Josh, but he sold the only two he brought with him to the tech session. Now I am more suspect of the AD itself. I have a replacement AD, perhaps I should just replace it and see if that solves the issue. I wish I would have gotten more done to my cars at the session. Dang.
Location: CLE/PHX
Posts: 2,613
My VIN: 5646,5080, 5880, 10234, 3639, 2518, 10586, 1538
www.deloreanindustries.com Every Detail Matters
Location: Lexington, NC
Posts: 817
My VIN: #5000 (Grey, manual, SS chassis, intercooled twin turbo), #16128 (Grey, auto, efi twin turbo), #888
Club(s): (DCVA) (SEDOC) (DCUK)
That is first class customer service Josh. Keep me informed please on the proper timing required. I'm also trying to enlist the help of Walter since he is in town for the rest of the week.
Location: Baton Rouge, Louisiana
Posts: 3,047
My VIN: 16510 and carbureted
Club(s): (GCD) (SEDOC) (DCUK)