PDA

View Full Version : Need help with a B28F fuel problem



TestPoint
07-16-2012, 10:45 AM
Please forgive the intrusion of a Volvo nut but I have discovered that the DMC folks know a lot more about the B28F engine than the Volvo dudes. The PRV is not held in high regard 'over there'. Most prefer the tractor engines.

Long story but I found an '81 Volvo Bertone Coupe in a barn in TN with 25k original miles on it. The elderly owner had attempted to get it running after 19 years in storage after his wife died. A local tune up shop worked extensively on it without success. They cleaned the rusty fuel tank, installed a tank pump, a pressure pump, filter, spark plugs, plug wires, distributor cap and rotor and generally took everything apart and put it back together. The 'take apart' included the fuel distributor which then leaked.

http://i772.photobucket.com/albums/yy4/tporterellijaycom/Volvo%20Bertone/P6220932.jpg

I bought it in non-running condition and have succeeded in getting it running . . . but not well.

Found corroded fuses and the relay contacts in both the pump relay and Lambda System relay were corroded and erratic.

Found several vacuum leaks in cracked and broken 31 year old hoses and connectors, the gasket between the upper and lower air plate assembly was only half installed, the 'ram horn' connection to the intake manifold was connected with bolts too long and therefore not sealing. Bolts were broken and washers missing all over the top of the engine. Found the spark advance at 10 degrees before TDC. In short, Elroy, the Master Oil Change Technician that had worked on the car to the tune of over $2,000 left a mess. I replaced the O2 sensor which was dead, had the fuel distributor rebuilt, replaced the Lambda Module which was the wrong one for the car, tested the injectors, tested the line pressure, and the control pressure, and set the CO adjustment using the dwell settings found on this forum. Oiled the distributor wick, which was dry as a bone, and set the ignition timing to specs. Found the spark coil resistor out of spec and jumped that.

The line pressure is 72 psi, the cold engine control pressure is 38 psi and rises to 52 psi in 5 minutes as it should. The cold high idle drops at 2 min, 35 seconds, the 066 Control Pressure Regulator loses its vacuum at about the 125 degree spec. Dwell at idle is 30-40 on the 4 cyl scale and drops to 28-32 at 3k rpm. The Frequency Valve seems to operate correctly as it is buzzing and passes fuel back to the fuel return line under control of the Lambda dwell. The return line is clear. Ignition advance is 10 degrees at idle and advances to 30+ degrees at 2k rpms. The exhaust does not seem restricted.

I have not figured out how to view the control pressure while driving but it does not change when revving to stall speed.

The engine starts easily, runs smoothly, will rev to redline, runs to torque converter stall speed (2300 rpm) but bogs on throttle while driving it. What am I missing? Any suggestions?

Thanks for any consideration of an alien to the forum.

Bitsyncmaster
07-16-2012, 12:38 PM
Sounds like you know what your doing. So what are the problems your seeing with the engine?

82DMC12
07-16-2012, 12:48 PM
Yup, give us some more info on symptoms... Like exactly what is happening, when, and if the engine is cold or hot, etc.

TestPoint
07-16-2012, 02:46 PM
Never tried to drive it cold but when warmed up it just doesn't seem to have any power, it bogs down if you give it any significant amount of throttle. It will die after the throttle bog if you let up on it. Can only get up to 50 mph or so and has great difficulty getting up the first 25 feet of my steep drive. Drive levels out after that so it runs OK then. Don't understand why it will run with throttle up to stall speed but not up a hill.

I disassembled and cleaned the throttle body and air flow assembly. Lightly lubed both and everything seems to function as intended. The throttle plate vacuum valves seem to function as intended.

Keeps feeling like fuel issue but other than a fuel distributor problem I am at a loss.

Exhaust blew out lots of water when first cranked after 19 years but it just doesn't seem restricted and know I keep putting off removing the cat because I know I will break off one or more studs doing that.

. . . and the original post stated that I found the spark advance 10 degrees before TDC. Actually it was found to be 10 degrees after TDC.

Bitsyncmaster
07-16-2012, 04:51 PM
Since you have checked everything with fuel, my guess is your CAT is plugged. When I have seen a plugged CAT, setting the mixture (Dwell) it would set but change and not hold the setting.

TestPoint
07-17-2012, 09:11 PM
OK, I give! I knew that if I pulled the cat I would break off the manifold studs and I didn't want to go there but this thing had got to get fixed!

I will be back in a few days after I buy the stud removal tool that will not work either and then the drill/easyout tool that result in a 5/8" bolt through the manifold flange.

Oh, Happy days!

nullset
07-18-2012, 06:34 PM
Keep in mind that revving the engine with no load on it is not nearly as stressful as trying to run it up with a load (trying to move the vehicle).

Have you done a compression test on the engine to make sure it's in good shape?

--buddy

TestPoint
07-18-2012, 08:02 PM
I have not done a compression test but plan on playing with the plugs this afternoon and will. Remember, this engine only has 25k miles on it. Unless the rings rusted to the cylinder walls it should be good.

I have rived the engine to torque converter stall speed in reverse which should have put quite a load on it. Runs fine there.

Thanks for the interest! All suggestions appreciated.

Next big test is to build a pressure meter that looks like an O2 sensor to measure the exhaust back pressure. I have a drawer full of questionable sensors but may have to venture out to the hardware store for a connector.

David T
07-19-2012, 10:28 PM
Sounds like vacuum leaks and you need to check and set the fuel mixture. You may also need to have the fuel injectors tested and cleaned. Get a dwell meter on the Lambda ECU and check the duty cycle of the frequency valve when it is warmed up. Best way to find all of the vacuum leaks is to "smoke" it.
David Teitelbaum

TestPoint
07-20-2012, 06:45 AM
I checked all the plugs and found them 'text book tan' and the compression uniformly 150 psi on a very leaky 40 year old compression gauge.

I have all the vacuum leaks fixed and the Lambda dwell is right where it should be.

Still trying to measure the exhaust back pressure before removing the cat. Two efforts at fittings failed but I know how to do it. Just didn't want to spend the money for a one time effort. I'll do that this morning.

dmc
07-20-2012, 07:50 AM
Before you go nuts. Put a timing light on it with your vac advance plugged and verify that your mechanical advance is working as the rpm,s increase. What you describe is classic symptom of a stuck distributor.

TestPoint
07-20-2012, 09:05 AM
Sorry if I have not posted all the fine details of this saga but here is the capsule version.

Spark plugs, wires, dist cap and rotor new. Plugs the perfect tan color. Ignition timing 10 degrees BTDC at 1000 rpm idle, advances to 20 degrees on centrifugal advance alone and 30+ degrees on vacuum advance at 2000 rpm.

Compression consistently 150 psi with a leaky gauge. Add 5 psi for the leaks.

Dwell set at 30-40 on 4 cylinder scale at idle and drops to 28-32 at 3000 rpm. The frequency valve is operating and I removed the output line to verify that fuel is indeed flowing to the return line.

Line pressure is 70-72psi, control pressure rises from 38 to 54 under heater control of Control Pressure Regulator. CPR loses vacuum at 125 degrees at Thermal Control Valve closing. Fuel distributor professionally rebuilt. Injector spray perfect by visual inspection.

Engine starts easily, idles at just under 1,000 rpms with no hint of missing, will rev to red line, pulls fine to torque converter stall speed (2300 rpm). Several vacuum leaks fixed. Consistent idle seems to confirm that that issue is over.

Bogs on throttle and won't pull a hill while driving. That last comment is strange as it will certainly run at the stall speed without complaint.

Today playtime is to test the exhaust back pressure. Tried to find fittings to match CO balance port unsuccessfully. Going to pick up a spark plug air connection in a few minutes after the caffeine kicks in. That is the thing you use to apply air pressure to a cylinder to hold the valves up while replacing the stem seals. That should be the same as the O2 sensor connection.

That's all I could find to test, repair and verify. Other thoughts appreciated.

nullset
07-20-2012, 11:16 AM
Are you sure it's not a problem with the transmission?

--buddy

David T
07-20-2012, 11:23 AM
I agree, the next thing to check is the mechanical and vacuum advance.
David Teitelbaum

TestPoint
07-20-2012, 11:39 AM
I have counted all three gears. It has difficulty going up my steep drive in LOW. Bogs if you give it too much throttle.

The distributor vacuum advance is exactly within specs.

DMCVegas
07-22-2012, 04:05 AM
I don't know what the Cold Engine specs on that engine are. DeLoreans like 760s idle around 1,200± RPMs when cold, and 750± or so once warmed up. 1K sounds a bit odd to me, but who knows.

Had a very similar issue on my car years ago. Turned out to be some bad ignition wires. Bust out the multimeter and check the impedance on your Ignition Wires to ensure they're in spec. Idle was fine, but when you hit the gas it went:
vvvvvvvvrrrrrrrRRROOOMMMMMMM!!!!!!!!!!! and would be ok once it was above 2,200 RPMs or so.

Aside from the vacuum advance, this would be something else to check as well.

ramblinmike
07-22-2012, 06:34 AM
Sounds like you've got the fuel side working properly. Go for simple things!

Check firing order. I've seen engines that idled fine with wires crossed but had major drivability problems.