Spittybug
03-15-2013, 08:56 PM
Word of advice for anyone with plastic Tees in their heater hose lines: replace them!
I have a bleeder line from the water pump over to the overflow bottle where it tees with the hose running to the heater core. I've had a white plastic (not nylon, seems more like a talc or glass reinforced PVC perhaps?) in that line for several years with no problems, until now. These claimed to be usable for heater hoses, not simply for vacuum.
I went to my beer brewing supply house today with my son and we took the D for a drive on such a beautiful day. Everyone and his G&*@!D brother, sister and aunt was driving on the roads today and we sat in some nasty jams. I noticed the temp creeping up and reminded myself to re-bleed the top radiator hose once I got home. The fans would kick on and bring the temperature back down again. Still, the swing had me anxious. We got stuck behind a multicar pile up on the beltway with no off ramp nearby. Sure enough, the temp would climb, come down, climb come down... then, just as the traffic started to move, clouds of white steam all over.... damn... I'm in the fast lane right by the toll plaza, about 8 lanes wide! I shut it down quick and played the start, accelerate, shut down, coast game for a couple of minutes as the traffic dissipated and I could get to the next exit. Immediately pulled into a U haul store. Yup, the plastic Y connector had failed on 2 of the legs and was dumping antifreeze all over.
I connected the water pump line straight to the nipple on the overflow bottle and took the heater line and wedged it in the open mouth of the overflow once the cap was off. I used the remainder of the Tee and the hose clamps to make sure it didn't pop out. I filled up with water, tested my open system and drove the remaining 5 miles or so home keeping my eye on the temp gauge. It never broke 160. Stopped at O'Reilly and bought a brass Tee and a jug of antifreeze. Got home, hosed the entire engine down to remove the residue and installed the Tee. Point worth noting; Hervey's spark plug wires and boots were soaking wet and the water pooled on the engine was deep around the plug boots. No problem starting or running as the water was kept out.
As luck would have it, a nice day, no pressing time constraints, close to home, relatively simple problem and fix....all ended up being a good learning experience for my son who isn't particularly technical. It let him see how understanding how things work can really help and that it pays to have a couple of tools with you.
I have a bleeder line from the water pump over to the overflow bottle where it tees with the hose running to the heater core. I've had a white plastic (not nylon, seems more like a talc or glass reinforced PVC perhaps?) in that line for several years with no problems, until now. These claimed to be usable for heater hoses, not simply for vacuum.
I went to my beer brewing supply house today with my son and we took the D for a drive on such a beautiful day. Everyone and his G&*@!D brother, sister and aunt was driving on the roads today and we sat in some nasty jams. I noticed the temp creeping up and reminded myself to re-bleed the top radiator hose once I got home. The fans would kick on and bring the temperature back down again. Still, the swing had me anxious. We got stuck behind a multicar pile up on the beltway with no off ramp nearby. Sure enough, the temp would climb, come down, climb come down... then, just as the traffic started to move, clouds of white steam all over.... damn... I'm in the fast lane right by the toll plaza, about 8 lanes wide! I shut it down quick and played the start, accelerate, shut down, coast game for a couple of minutes as the traffic dissipated and I could get to the next exit. Immediately pulled into a U haul store. Yup, the plastic Y connector had failed on 2 of the legs and was dumping antifreeze all over.
I connected the water pump line straight to the nipple on the overflow bottle and took the heater line and wedged it in the open mouth of the overflow once the cap was off. I used the remainder of the Tee and the hose clamps to make sure it didn't pop out. I filled up with water, tested my open system and drove the remaining 5 miles or so home keeping my eye on the temp gauge. It never broke 160. Stopped at O'Reilly and bought a brass Tee and a jug of antifreeze. Got home, hosed the entire engine down to remove the residue and installed the Tee. Point worth noting; Hervey's spark plug wires and boots were soaking wet and the water pooled on the engine was deep around the plug boots. No problem starting or running as the water was kept out.
As luck would have it, a nice day, no pressing time constraints, close to home, relatively simple problem and fix....all ended up being a good learning experience for my son who isn't particularly technical. It let him see how understanding how things work can really help and that it pays to have a couple of tools with you.