May I ask why you did it like Bill in the first place?
Printable View
Ah, thanks.
I was wondering why he would want to up the voltage with a hot coil then choke it with a resistor (on a point-less system).
FWIW: The Blaster 2 sheet says a resistor is not required (2nd column, just before "Removal" instructions).....
That was the first thing I noticed. In fact, there are quite a few things wrong with the video. However, the finished product should look slightly better, and also be funnier. :)
Someone pointed out to me that I should have writ "OZZY" on my left hand's fingers as he evidently did that when he was a teenager. So add that to the list. :lol:
Farrar
Now that is a loaded question if I ever saw one LOL!!!
Seriously, points or electronic, it's just a switch, a trigger for when to fire the coil, nothing else. The gap recommended by the manufacturer(s) is determined after considerable testing of the spark's curve and resulting burn for a given engine.
(This has been pointed out several times, by several people, in several threads to no avail -- no offense or implication directed toward you whatsoever! -- A stinking can of worms that needs to stay shut at this point IMO ;-)
If it was points based it would have points, no?
I don't know what that looks like. Although the book I have at home on automotive tune-up and maintenance mentions "points open" and "points closed" for certain tests, it does not contain illustrations. Ignition is the one system on the car I have not yet studied in detail, and I am a slow learner.
Farrar
It's all just two ways of doing the same thing. Just look at the pictures in the link below ;-)
(If you care to read it, notice the purpose of the capacitor (condenser) is for more than radio noise suppression, another myth floating around...)
http://www.familycar.com/Classroom/ignition.htm
A second thought on the resistor- When replacing a point based system with a "breaker-less/electronic" upgrade, every one I have seen has a full 12V feeding it.
Ron,
So we are running points...? I seem to recall seeing something of that type underneath the ignition distributor's dust shield. I dunno, I will look again. In the meantime, I will take some notes from that article you pointed me to. Thanks!
BTW, if memory serves Bill's justification for wiring the thing the way he did is that by bridging that one side of the stock ballast resistor, he gets .25 Ohms of resistance and 12.5v into the coil. I don't know how he did that math, but he presumably measured the 12.5v with his voltmeter. I put a glass fuse on the other side of the resistor just to be safe; I believe Bill has a fusible link in the same place.
Farrar
No points, no condenser, no need for the resistor according to the sheet as I read it and, IMHO, no need to second guess the engineers therefore no reason to replace a stock coil (Now you happy that you drug it out of me LMAO)
No need to figure the resistance when it says not to use it...Now, Bill may have had another reason --that all depends on what else he, or someone else did, although I can't think of why, unless it is the cap and rotor not being able to handle it. FWIW would ask him. Since he chooses to hide in the shadows I can only respond with:
http://www.youtube.com/watch?v=hzbrlSHf5-M
Back in 2008, I was informed that if I wanted to run a wider plug gap I would need to upgrade the ignition coil. I did so. There may have been no need to replace the stock coil -- for all I know I could have simply removed the ignition bypass relay and ballast resistor and left the stock coil in place -- but I did so anyway. Sparky's blue coil is gone -- besides, it would be thirty years old by now. I might as well try to do the best with what I've got.
Who knows, ignition could be a wild goose. Sparky's rough running may actually be caused by a vacuum leak. Perhaps I will buy a cheap fog machine from Party City, take the carburetor off the manifold and stick a tube between the fog machine and the intake manifold, then see if any fog comes out anywhere. (I proposed this "poor man's smoke machine diagnostic" method last year on the old DMCTalk since I found out that "fog juice" is merely propylene glycol and therefore not harmful to our engines; since then, evidently David Teitelbaum has had success tracking down vacuum leaks using this method.) I didn't think I had any vacuum leaks, but I've been wrong before.
Farrar
If you want a wider gap then you may very well need to get a hotter coil. The thing, to me, would be why would you want a bigger gap. Racers do/did it because they changed their stock design-configuration, as did manufacturers (in fact they are easing the other way since they are accomplishing near complete burn with new designs). Changes to your D's configuration, may have required it too, or, you may just simply want to, of coarse.
I like the fog machine!!! Similarly, I have pulled a carb, to make it easier to seal things up, and blew a controlled amount of pressure into the engine to chase down an air leak ($%#&*%! internally cracked intake runner).
As I said before, I would chase down the missing cylinder(s) -- this makes it easier to pinpoint the problem. I always try to look for the obvious, then pair up easiest with most reveling test(s).
From the sound, I'm doubting vacuum leaks, too...there is definitely more than that anyway.
Bill and I e-mail frequently and he still thinks it's a vacuum leak. The fact that it doesn't seem to miss at higher RPM would seem to bear that out, but I have torqued down the intake manifold more than usual, with brand new O-rings underneath it, and pulled a vacuum on all the lines to confirm no leaks.
Bill still says I should spray brake cleaner or carburetor cleaner all over the intake manifold mating surfaces and see what happens. That stuff smells awful and makes my eyes burn. Besides, since there is hot engine oil leaking into my engine valley whenever I run the thing, and I have already had a fire in the engine compartment on this car, I hesitate to spray oodles of highly-flammable liquid down there. What if I got some warm tap-water in a spray bottle and used that instead? Would that be sufficient for a vacuum leak check?
Farrar
Maybe I need some propane...
http://www.youtube.com/watch?v=9CPqbaSgcok
... or a cheap cigar! :lol:
http://www.youtube.com/watch?v=zMok2y05jNE
Farrar
With exhaust, distributors and sparks in general, water can be a lot safer. I think 'spray spirts' all around... sounds safer LOL. I find a small water stream works better than a spray bottle. Instead of listening for the engine to rev etc, you listen for it to settle and smooth out and/or a slurping sound, or, a change in general. -- Be careful around oil puddles, the water will cause them to pop like bacon grease. Of coarse you don't want the engine to be "HOT".
Air and soapy water is another option...sizs and location matters ...but you can only suspect....
I used to smoke a pipe. I still have two pipes at home, but I haven't done anything with them in a while. They're probably no good anyway, but they do look pretty.
I bought a 99¢ cigar yesterday afternoon, so I am all set to do the test. I will remove the carburetor and seal the top of the intake manifold with duct tape, then cap off one of the manifold vacuum ports and stick a long hose on the other. After that I will be ready to do the test. All I need to do is find the time to do it, which is difficult this time of year.
I really do wish I could drive the car right now; when I walked out of the apartment this morning to go to work it was 68°F with low humidity -- perfect window-open driving weather, no need for air conditioning.
Farrar
Bill would be proud. You better fix that car soon. Our little shin dig is this Saturday.
If it makes you feel any better I am currently without AC as well. I messed up my crankshaft pulley pretty bad when I was taking off the nut that holds it. Fortunately the part that runs the water pump and alternator is fine but the AC section is whop sided like the tire on my bike.
Oh, man, I forgot all about that!
Well, if I do have a vacuum leak around the intake manifold there is little I can do about it -- I put fresh O-rings under the manifold and tightened down the intake manifold's bolts as tight as I dare (the heads started rounding off). And don't forget, my oil leak is back so every time I drive the car it collects oil in the engine valley.
I have a gig Friday night (see video) but it should be over with by 10pm, which means I may be able to get a decent amount of sleep before Saturday morning's shin-dig.
http://www.youtube.com/watch?v=WdgXM6MSWMY
Farrar
We can easily fix your oil leak if is due to a bad valve cover gasket.
Part # VS26090 is available from Autozone. They may have to special order it but if you go in the store today they should be able to have it for you by Friday. I ordered my set from Rock Auto and it was about $12.
It shouldn't take more than an hour to do the work and it would make a nice tech session repair.
Shoot, it looks like I was wrong. A quick search of Autozone.com indicated it is no longer available. You could get the gaskets from Rock Auto though. They ship pretty dang quick.
Edit: I posted this too soon. Disregard what I said.
The timing cover gasket is a piece of cake once you get the crankshaft pulley off. We could do that for you Saturday as long as the nut easily comes off.
In your case, yes... because you don't have a big muffler in the way like I do! On my car, I doubt I could get a wrench in there with sufficient torque to get the nut off. I was hoping I wouldn't have to get the timing cover off until I switched to dual exhaust...
Farrar
I am still not sure what I am going to do about my exhaust -- Houston's headers flow better so I would like to keep them, but they are beginning to rust, besides I am not sure they could be used for two mufflers because of their length. I will have to make some careful measurements the next time I have the car in the air. That work is a very long way off -- first vacuum leak, then air conditioning.
Farrar
You guys should exchange phone numbers....
This thread is public so that anyone can jump in with a comment at any time. (Case in point: your post above.) Just because there are only two people engaged in a discussion for a few minutes does not make it a private discussion.
Other people have said in the past that they read this thread while not necessarily posting in it, and I assume they were not lying to me, so I will continue to keep the discussion open since nothing of a sensitive nature has been thus herein discussed, nor is any such information likely to be disclosed in such a public forum.
Unless you were just trying to be funny, in which case :lol:
Farrar
Would anyone be interested in sharing a room with me for DCS?
If I didn't have the family coming with I'd do it.
Attachment 5951
The nut on an instrument of the viol family is that small light-colored piece or plastic/ivory at the very top of the fingerboard. It has indentations in it to help hold the strings in place. If your instrument is cheap or badly-maintained (and his was) it is possible to break the nut at one of those indentations as they are naturally that piece's weak spots.
Back on topic: found out that the small cigar I bought at the gas station is grape-flavored. Ew! I am glad I don't need to smoke it for very long to do my test.
Farrar