Ah. Absolutely not the case with the DPNW part. No comment on if one could then infer that it was the other, competing hard plastic bushing that would need modification to work properly. ;)
Printable View
Thanks to Steve Rice, Sparky is back on the ground now. His floor jack is superior to mine in two ways: it is shorter, and it raises higher. I was unaware that there was such a thing as a "low profile jack" until now -- so I am going to buy one since I am tired of crawling under the car and lifting it with my shoulder to get the jack underneath. The Duralast jack that I bought will live in the PT Cruiser in case I ever need to change a tire.
I have confirmed that the drip I found is gear oil from the final drive, leaking out around the passenger-side output flange. Looks like the Grady seals I got were either installed incorrectly or not up to the task. (And yes, we also installed the O-rings and sleeves when we did the job a year or so ago.) Those seals felt good to me so I doubt they were NOS but rather newly manufactured. Nonetheless, I have heard good things about John Hervey's double-lip seals. Since I am going to buy one of his rebuilt axles anyway, I might as well add those to the list.
I *have* John's double-lip seals but have not installed them yet. They look to be really top quality stuff. I actually have them for the output shafts as well as the front and rear main engine seals. I did install the front (crank pulley) seal and it seated nicely and fixed that leak instantly. No felt to wear out.
Strangely, the O'Reilly Auto Parts store website says that they have the output shaft seals in stock, but only for the automatic transmission. Since I remember quite clearly what the seals look like, I may go and have a look at what they have. I can't believe they would be correct, so if nothing else I can report to them that they need to change the listing on their website.
That would be interesting, because the seals are the same for manual/auto.
I had to go somewhere else instead, so I will check O'Reilly tomorrow. In the meantime, my vacuum hose has come in. I got 1/8" thick blue silicone hose from McMaster to redo all of my vacuum lines -- and I mean ALL of them, including the ones inside the car. The firm silicone grips very well, and I have had a problem with some of the old hose letting go. I also plan on replacing the hard plastic line that goes through the car with a contiguous silicone run. Although black hose is available, I got blue to make it different from all of the other black hoses in my engine compartment. (I would like to eventually get another color for the coolant hoses -- preferably green. But that's a long way off.) The only drawback with the blue McMaster hose is that it's translucent, which means that eventually parts of it will look ugly with oily residue inside. But now that I think of it, translucent air hose would also be diagnostically useful -- easy to see if I have a block or kink somewhere, or if the engine is sucking oil badly. Anyway, it doesn't matter since I am the only one who will ever look at it. :)
Tomorrow will be a big day -- I plan on taking out the driver's seat to fix the stud, and replacing the vacuum hoses and intake manifold O-rings. Then if I am lucky I can fire up the engine and see if I have a vacuum leak.
I did not get around to installing all of the silicone hose today, but I did get to install the new O-rings under the intake manifold. I saw evidence of a vacuum leak in the form of stains where I took the old O-rings out -- the edge where the O-rings push in is very sharp and the O-rings had been cut by it. So this time I oiled the O-rings generously before putting them in. Although I didn't get a chance to start the engine, I was also able to install my security system, so I accomplished two things today! :D
Damn, I was hoping it would be one of these...
http://www.youtube.com/watch?v=fBI0hmwISdA
1. English paper (just finished)
2. Lunch
3. Grocery store
4. Math homework
5. Song transcription for one of the two bands I'm in
6. DeLorean
Those are my priorities of the moment. Supper may get in there somewhere, but I hope to get to the car before it's dark. Fingers crossed!
I only got as far as #4. :( Good night.
In other news, I think I found out what a strange and occasional "thump" coming from the left rear of my car was coming from: a loose body/frame bolt. The bolt which screws into the captive nut in the end of the frame on the left side (17mm hex head, so presumably a M10x1.5 bolt) was so loose that I could turn it with my fingers. When I looked on the other side, I found that nut and bolt to both be missing entirely! I tightened the bolt and hope it solves the "thump," but now I realize the proper course of action would have been to remove both the nut and bolt, then take them both to the hardware store and get stainless steel replacements. Unfortunately, it's supposed to rain all week.
Finally got a chance to get the pictures off of my camera from Saturday.
Attachment 8708
That brown "stain" at the top of the recess for the O-ring looks like a possible vacuum leak to me. Perhaps the O-ring was damaged by the sharp edges of the recess in the block and created a leak. The edges of the chambers inside the intake manifold are also sharp, so I have to be careful how I put it on.
I lubricated the new O-rings before installing them.
My battery evidently was not very well-charged by the short drive I made with the car a few weeks ago -- just four days after installing a blinking red light, it had stopped blinking. :lol: Fortunately, I have a good battery in the daily driver and a long set of jumper cables.
From the "One Thing Led To Another" department:
I decided to replace my vacuum lines today and this is what happened.
I knew this seat stud was broken...
http://www.youtube.com/watch?v=sa7HFNpOroo
...but I didn't know about this one!
http://www.youtube.com/watch?v=-MgGNt-tEEM
Water caused bunches of rust and for the wood to completely separate on the passenger side...
http://www.youtube.com/watch?v=TlrMXJcwNio
...but the driver's side wood is mostly attached.
http://www.youtube.com/watch?v=eNjyisa4X7M
HEY, WHERE'S MY STEERING COLUMN BUSHING? Oh, well -- least of my worries at this point.
Sparky's previous owner evidently skimped on fasteners:
http://www.youtube.com/watch?v=Kbo8QVEPuGw
Here is where I stand now:
Attachment 8769
Attachment 8767
Attachment 8768
Attachment 8770
Attachment 8771
I may not make it to Orlando in June.
Not at the rate I am working... :(
This is the first I have heard of Bill threatening, um I mean offering to come down. ;D
Bear in mind that on top of the damage I found to the interior, I still have no a/c -- it was 87 degrees during winter here so you can guarantee we will be driving to Orlando in record heat. I also haven't figured out why the cruise control doesn't work. A ten-hour drive with no cruise control is murder on my right leg. And I haven't even fixed the vacuum leak yet.
I think my car might scare Bill away...
Now I have to save up money for new carpet. I can survive on ham sandwiches and lemonade, but my girlfriend is used to a higher gustatory standard... saving that kind of money between now and June will be difficult... or I could just drive without carpets. :lol:
Okay, so this is interesting...
When I took the seats out, I noticed that there appear to be thick washers adhered to the driver seats but not the passenger seat.
Lo and behold -- someone installed all eight washers on one seat.
Attachment 8773
And of course they're all stuck together.
This car just gets more and more interesting!
One more question: these are body bolts, right? Can I assume that they connect with the frame?
Attachment 8774
If so, then they are ground points. I may not be running a ground bus like Bill, but if these are good grounds, then I think I may have found a place to ground my inertia switch!
Thanks. That reminds me, I need to order some M10x1.5 bolts and square washers to replace the body bolts in the engine compartment. I am adding them to my McMaster order...
Oh, and I checked out what O'Reilly had listed as an output flange seal. National Part #1962. $4.06 including tax.
Attachment 8795
Attachment 8796
Attachment 8797
Attachment 8798
Looks like OEM to me.
McMaster order placed:
- Black #6 sheet metal screws and finishing washers to replace all of the oddball, "make it fit" ones in the interior of the car.
- Stainless M8 lock-nuts to replace the rusted original lock-nuts under the seats.
- Nylon M8 washers for the lock-nuts above.
- ¼"-20 jack-nuts, enough to replace all of the ones in my rear fascia (installation tool included).
- Stainless hardware for the license plate surround and taillight lenses.
- New large washers for the seats.
- New M10x1.5 body bolts and captive nuts for the engine compartment.
Time for a ham sandwich and glass of lemonade.
Yes, at first I thought they were corroded together, but when I got that pair loose I noticed that they were actually adhered on purpose. Now this explains why the driver's seat always looked like it sat slightly higher than the passenger seat -- the question is: why was this done? If it's on more than one car, there must have been a reason for it. I am tempted to just put one washer around each stud on both seats before I reinstall them, but if there was a good reason to put all eight washers on one seat, then maybe I should find that reason before I start playing with the JB Weld and Rustoleum...
Just thought of something: if the wood behind the passenger seat has come undone from the bottom, that means there are only a few screws holding it onto the other panels, right? I should be able to remove it. A friend of mine has access to a big work table and a jig saw, so we could cut a replacement panel.
Without the washers under the seats, you will have a hard time sliding the seat forward or aft. I think it makes clearance for the carpet to not rub when sliding the seat.
Thanks. Good thing they come in packs of 100...
FYI, I ordered washers with a 10mm hole and 20mm outer diameter. That's not quite as wide as the original washers, but I couldn't find anything available in that exact size. And at 2.2mm thick I think they will do the job of raising the seats past the carpet.
In other news, can anyone think of a material which is just as strong as 1/2" plywood but not as thick? I am considering replacing the wood panels behind the seats (one of which was damaged by water anyway) and would like to adhere some soundproofing material to the back. But the soundproofing material is at least 1/4" thick. That means the panels would have to be half as thick as stock. Lighter than plywood would also be good, but I am sure that's a tall order -- for light weight, strength, and durability, it's hard to beat The Original Carbon Fiber©.
Any thought given to some thin plywood wrapped in fiberglass? You could probably cut the thickness in half and still be plenty strong with a few layers of fiberglass.
That's a good thought. I wish I had access to my porch right now as there are a number of things I would like to make out of fiberglass... unfortunately, they're renovating our building so for the next few months I have no outside space to set up a workbench. I figure, however, that I can get away with setting up a couple of sawhorses in the parking lot one Saturday or Sunday when the weather is good, run an extension cord out the apartment window, and cut a new panel.
What about buying a sheet of 1/2" fiberglass and cutting it to fit? Can you cut fiberglass with a jigsaw or saber saw? Would the edges need to be re-epoxied for strength?