Hey, what does "RTVd " mean? :hmm:
RTV
Return To Vendor
Room Temperature Vulcanizing
Take your pick
David Teitelbaum
I have never had a problem tightening my alternator. Its just one heck of an inconvenience because I use a floor jack to lift the alternator when tightening the belt. The only reason I would buy the fancy bracket is to be lazy and not have to take the heavy jack out of the trunk. But honestly, how often do I have to tension my alternator belt?
Total expenses to date: $211.4616
Expense #1 (Radiator Leak) - January 7, 2012 - 44,079 Miles - Total Cost: $117.83 (including tax)
Expense #2 (Radiator Leak) - January 15, 2012 - 44,386 Miles - Total Cost: $7.40 (including tax)
Expense #3 (Replaced windshield wipers) - January 15, 2012 - 44,386 Miles - Total Cost: $17.54 (including tax)
Expense #4 (Oil Change) - January 21, 2012 - 44,643 Miles - Total Cost: $24.4616 (including tax)
Expense #4 (Reinstalled steering column bushing) - January 22, 2012 - 44,693 - Total Cost: $1.35 (including tax)
Expense #5 (bought coolant and water) - February 20, 2012 - 45,000 - Total Cost: $11.88
Expense #6 (replaced rear interior light) - February 23, 2012 - 45,500 - Total Cost: $31
Thanks to Farrar I spent another $31 on something I didn't really need. A while back he ordered us some fancy Porche dome lights and last night I got around to installing mine while at his apartment. It set me back a whopping $31. I didn't need it since my old one worked, but it was falling apart so I decided to replace it anyway.
I'm almost half way to my yearly budget and February isn't even over yet! :dead:
Attachment 8741Attachment 8742
Well I was on my way to church this morning and this happened. I bypassed it but the one gallon of coolant I carry was not enough to refill the system.
I was on interstate when it happened and was about 3 miles from the nearest gas station. Instead of calling someone to bring water/coolant I used my manual transmission to coast and glide the next 3 miles using the engine to speed up to 55 mph and shutting it off until I slowed to 35 mph. I did this a few times and was able to reach the gas station without overheating.
I filled up with tap water and made it home without a problem.
Now I'm going to have to flush the system because of the stinking tap water. Oh well, I need to pull the radiator anyway.
Incidentally, do any vendors sell heater control valves that are completely metal. This is the second plastic one I've had from Hervey to break.
Wow. I wonder what Grady has. Hervey might repalce it under warranty but I'm not sure how long the warranty is on this part. I know I've had it at least a year.
And here goes another thing to debate. If all the vendors have is plastic, perhaps I should just go down to Autozone and see if they have one of this. I've I'm going to be getting plastic anyway, it might as well have a lifetime warranty.
And here is the official Stevedmc cross reference information.
http://www.rockauto.com/catalog/moreinfo.php?pk=380367
Motorcraft Part # YG136
FORD BRONCO (1980 - 1994)
FORD E-100 (1979 - 1983)
FORD E-150 (1979 - 2004)
FORD E-250 (1979 - 2004)
FORD E-350 (1979 - 2004)
FORD E-450 (2000 - 2004)
FORD E-550 (2002 - 2003)
FORD F-100 (1974 - 1979)
FORD F-150 (1975 - 1979)
FORD F-250 (1974 - 1979)
FORD F-350 (1974 - 1979)
FORD FAIRLANE (1969 - 1970)
FORD FAIRMONT 1978
FORD FALCON (1969 - 1970)
FORD FIESTA 1978
FORD LTD (1969 - 1978)
FORD MAVERICK (1976 - 1977)
FORD MUSTANG II (1974 - 1978)
FORD PINTO (1974 - 1978)
FORD THUNDERBIRD (1968 - 1976)
FORD TORINO (1971 - 1976)
LINCOLN CONTINENTAL (1973 - 1978)
LINCOLN MARK III 1969
LINCOLN MARK IV (1972 - 1976)
MERCURY BOBCAT (1975 - 1978)
MERCURY COLONY PARK (1969 - 1971)
MERCURY COMET (1976 - 1977)
MERCURY COUGAR (1969 - 1976)
MERCURY GRAND MARQUIS (1975 - 1978)
MERCURY MARAUDER 1970
MERCURY MARQUIS 1972
MERCURY MONTEGO (1973 - 1974)
Oreilly Auto Parts sells a part identical to what I have but it costs $28 and only has a one year warranty.
AutoZone has a part that appears to be all plastic (unless the image is wrong), doesn't look the same, and the website doesn't specify how long the warranty is. The AutoZone part is only $10.
Sounds like in addition to a bottle of antifreeze you should carry a 5/8" hose coupler in your car at all times in case of such an emergency. At least I think it is 5/8"... I have not gone outside to look at my car yet today.
If I remember correctly, the vacuum line that goes to the heater control valve shuts off the flow of hot water to the heater core when the air conditioning is set to "max." So in theory you could run without the heater control valve, but if you ever select "max" on your a/c you would have a vacuum leak -- and of course your a/c would not be as cool. I am not sure if the heater control valve has anything to do with heat or if it is just part of the air conditioning system, but I am sure someone else who knows better can chime in with this information.
Edit: after your two failures, I am getting nervous about my car's heater control valve!
What's ironic is I think the original valve was all metal. I replaced it because it was 30 years old and had lots of corrosion on it. Had I know I would have these problems I would have just brushed it off and left it in there.
I'm seriously thinking of getting two of the $10 units from autozone to keep one as a spare. I haven't had much luck with the motorcraft part so it can't hurt to try something different.
I know they're just plastic but it really seems odd that they'd fail at such a high rate in your car when the cross-reference indicates that it's such a widely used part. I wonder if there could be something in how your hoses are routed that is putting strain on the plastic bits? Maybe there's a way to provide additional support to those supply hoses that would help increase the lifespan of the valve.
This is where I believe my repaired radiator is leaking. It appears to have a new weld in this spot.
Attachment 8766
The first failure I suspect to be my fault. I think I tightened the hose clamp to the plastic barb to tight and after a few weeks the part failed. I called Hervey, told him what happened and that I suspected it was my fault. He shipped me a replacement very quickly and didn't even ask me to send the old one back. It may have been my fault, but Hervey decided to replace it under warranty.
That was at least a year and a half ago. When I installed Hervey's replacement I made every effort to only tighten it enough to prevent from leaking. Well, it held up until this morning.
The only thing I can think of is I was sitting in stopped traffic for about 10 minutes. Most of my driving is at highway speeds and it isn't normal for me to stop with the engine running for extended amounts of time. Well, since air wasn't blowing over the radiator the temp gauge started to creep towards the half way mark. In my car the fans kick on at the half mark and run until the needle goes back down to the quarter mark so I was just watching the needle waiting for it to start going down.
Just after the temp gauge read half way, traffic started moving. I started driving expecting the highway air to bring the needle down to the quarter mark. Well, just as I was changing lanes I looked behind me and saw steam coming from the engine bay!
I didn't suspect this to be due to low coolant since I had topped it off before I got on the road. My radiator leak has been very minor and I've been doing fine just topping the thing off every couple hundred miles.
Upon inspection in the engine bay I found the valve had broke and that I had tons of coolant in my intake valley. I will remove my manifold later today to do the necessary cleanup. It is a good thing it only takes 3 minutes and 18 seconds to get to my valley.
Anyway, the only thing I can think of that might have triggered the problem with this control valve was the extended time I spent in traffic.
My AutoZone replacement was $10.39 with tax and comes with no warranty. I'll update the running total one it is installed.
Attachment 8775
Total expenses to date: $221.8516
Expense #1 (Radiator Leak) - January 7, 2012 - 44,079 Miles - Total Cost: $117.83 (including tax)
Expense #2 (Radiator Leak) - January 15, 2012 - 44,386 Miles - Total Cost: $7.40 (including tax)
Expense #3 (Replaced windshield wipers) - January 15, 2012 - 44,386 Miles - Total Cost: $17.54 (including tax)
Expense #4 (Oil Change) - January 21, 2012 - 44,643 Miles - Total Cost: $24.4616 (including tax)
Expense #4 (Reinstalled steering column bushing) - January 22, 2012 - 44,693 - Total Cost: $1.35 (including tax)
Expense #5 (bought coolant and water) - February 20, 2012 - 45,000 - Total Cost: $11.88
Expense #6 (replaced rear interior light) - February 23, 2012 - 45,500 - Total Cost: $31
Expense #7 (replaced heater control valve) - March 4, 2012 - 45,766 - Total Cost: $10.39 (including tax)
I replaced the heater control valve tonight with an el cheapo part from AutoZone. As documented earlier in this thread, I used a part cross referenced to a 1980 Ford Bronco. Unfortunately this AutoZone part does not have a warranty. If it breaks I'll have to cough up another $10 for a replacement.
Outside the box question - living where you live, how badly do you actually need a heater?
Recall that valve is only used to turn the heater core off on MAX-A/C. Any other time the valve is open. If you leave the valve out (i.e plumb around it) your A/C will not be quite as cold as it could. That's probably a big deal where you live.
OTOH if you bypass the heater completely, you won't have the valve to worry about (assuming you bypass it at the engine).
As for the failures, the valves don't often fail and I've replaced more due to rust than broken plastic. I've seen the valve leak where the lever is, and the vacuum inlet break off, but I can't say that I've seen the main plastic fitting break.
I could probably survive without heat, but we occasionally have winters as cold as 16 degrees. I wonder if I am doing something wrong or if I am just having bad luck.
I would think it wouldn't be possible to install this in reverse since its just an on off valve but perhaps I am installing them with the hoses connected the wrong way, resulting in my problems.
Oh well, the autozone part looks like it has some pretty thick plastic. I'll see how it holds up.
As Dave S mentions, the heater valve does not have a high failure rate. The fact it failed quickly and multiple times would suggest something wrong in your technique installing it. I have never seen one break, they either get stuck and won't move and/or leak. It may be possible if you overheat the motor you could "cook" the valve and make it more prone to breakage. It isn't an expensive part, just difficult to access and a little messy because of the coolant.
David Teitelbaum
I've never shifted the blame from myself to the part. I think I may have overtightened the dang thing somehow.
Anyway, its no big deal. I watch my gauges like crazy all of the time and I caught it before any real damage was done. It is also very easy for me to replace the part. You are forgetting how easy my engine access is vs a typical delorean.
Steve, just a thought here -
Last week I drive down to DMC NW from Vancouver to pickup some parts from Toby. I get down there and low and behold there is a pool of coolant under the car. After one cooling system incident last year I watch it like a hawk.
It turns out one of my heater hoses (that I installed over a year ago) was occasionally rubbing on the axle boot. When Toby and John cleared out their shop and put the car up on the lift (they deserve their own appreciation thread just for this btw!) you could clearly see there was too much slack in the heater hose (the one that leaves the heater valve bound to the heater core). Even with a little pull it would extend well below the axle if given the opportunity.
My point is that you should check and ensure your hose isn't getting caught up or tugged by the axle or axle boot. It seems to me it could be enough pressure over time to weaken plastic on the heater valve.
Total expenses to date: $245.5016
Expense #1 (Radiator Leak) - January 7, 2012 - 44,079 Miles - Total Cost: $117.83 (including tax)
Expense #2 (Radiator Leak) - January 15, 2012 - 44,386 Miles - Total Cost: $7.40 (including tax)
Expense #3 (Replaced windshield wipers) - January 15, 2012 - 44,386 Miles - Total Cost: $17.54 (including tax)
Expense #4 (Oil Change) - January 21, 2012 - 44,643 Miles - Total Cost: $24.4616 (including tax)
Expense #4 (Reinstalled steering column bushing) - January 22, 2012 - 44,693 - Total Cost: $1.35 (including tax)
Expense #5 (bought coolant and water) - February 20, 2012 - 45,000 - Total Cost: $11.88 (including tax)
Expense #6 (replaced rear interior light) - February 23, 2012 - 45,500 - Total Cost: $31 (no tax and free shipping courtesy of Farrar)
Expense #7 (replaced heater control valve) - March 4, 2012 - 45,766 - Total Cost: $10.39 (including tax)
Expense #8 (bought more coolant/water) - March 7, 2012 - 45,766 - Total Cost: 23.65 (including tax)
I dropped off my leaky radiator at a repair shop a few days ago and still haven't heard back from them. Hopefully they are repairing and testing it for free since I suspect it wasn't fixed right the first time.
Anyway, since I drained the coolant out of the system and have no spare coolant laying around the house I decided to make the trip to Wally World to purchase 2 gallons of coolant and 2 gallons of distilled water. The stuff is sitting in the back of my Geo Metro right now, waiting for the moment it gets mixed and put into the Delorean.
I just got off the phone with the radiator shop and the thing is ready to be picked up. I think I know what I will be doing tonight. Wish me luck.
And in June you will be glad that you don't factor fuel cost in your modest budget. ;)
Well, I got the radiator mounted but it was getting too dark to finish up so I called it quits for the night. Today after work I plan to finish connecting the hoses, tighten everything, fill the system with tap water, and then pressure test and drive the thing a little bit.
After I have verified there are no leaks, I will drain the water, blow the system out with compressed air, and then fill it up with coolant and distilled water.
I am not putting my precious coolant in this thing until I know it is leak free.
I do have a few concerns about their recent repair. My dad went and picked up the radiator for me and I was shocked to see how dirty it was and that they used some sort of expoxy to do part of the repair this time. I really hope the thing holds.
The first repair looked so professional but it obviously wasn't fixed. The current repair looks so redneck. We will see if it lasts or not.