FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 12 of 37 FirstFirst ... 2 10 11 12 13 14 22 ... LastLast
Results 111 to 120 of 370

Thread: How to maintain your Delorean for less than $500 a year and put 10,000 miles on it

  1. #111
    Not a DeLorean Guru
    Join Date:  May 2011

    Location:  Rochester, NY

    Posts:    2,405

    My VIN:    01049

    Quote Originally Posted by stevedmc View Post
    I've never shifted the blame from myself to the part. I think I may have overtightened the dang thing somehow.

    Anyway, its no big deal. I watch my gauges like crazy all of the time and I caught it before any real damage was done. It is also very easy for me to replace the part. You are forgetting how easy my engine access is vs a typical delorean.
    Mine too

    I need to replace my hot water valve as well; I managed to break that stupid brittle vacuum line connection on mine while I was re-assembling my top end.
    -Mike

    My engine twists my frame.

    1981 DeLorean, Carb LS4 swap completed
    1999 Corvette, cam/headers/intake manifold, 400 rwhp
    2005 Elise, stock
    2016 Chevy Cruze

  2. #112
    One of those purists you keep hearing about. sdg3205's Avatar
    Join Date:  May 2011

    Location:  Vancouver, BC

    Posts:    3,388

    My VIN:    thirty two 'o five

    Club(s):   (PNDC)

    Steve, just a thought here -

    Last week I drive down to DMC NW from Vancouver to pickup some parts from Toby. I get down there and low and behold there is a pool of coolant under the car. After one cooling system incident last year I watch it like a hawk.

    It turns out one of my heater hoses (that I installed over a year ago) was occasionally rubbing on the axle boot. When Toby and John cleared out their shop and put the car up on the lift (they deserve their own appreciation thread just for this btw!) you could clearly see there was too much slack in the heater hose (the one that leaves the heater valve bound to the heater core). Even with a little pull it would extend well below the axle if given the opportunity.

    My point is that you should check and ensure your hose isn't getting caught up or tugged by the axle or axle boot. It seems to me it could be enough pressure over time to weaken plastic on the heater valve.
    Dave

    Here, somewhere.


  3. #113
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Total expenses to date: $245.5016
    Expense #1 (Radiator Leak) - January 7, 2012 - 44,079 Miles - Total Cost: $117.83 (including tax)
    Expense #2 (Radiator Leak) - January 15, 2012 - 44,386 Miles - Total Cost: $7.40 (including tax)
    Expense #3 (Replaced windshield wipers) - January 15, 2012 - 44,386 Miles - Total Cost: $17.54 (including tax)
    Expense #4 (Oil Change) - January 21, 2012 - 44,643 Miles - Total Cost: $24.4616 (including tax)
    Expense #4 (Reinstalled steering column bushing) - January 22, 2012 - 44,693 - Total Cost: $1.35 (including tax)
    Expense #5 (bought coolant and water) - February 20, 2012 - 45,000 - Total Cost: $11.88 (including tax)
    Expense #6 (replaced rear interior light) - February 23, 2012 - 45,500 - Total Cost: $31 (no tax and free shipping courtesy of Farrar)
    Expense #7 (replaced heater control valve) - March 4, 2012 - 45,766 - Total Cost: $10.39 (including tax)
    Expense #8 (bought more coolant/water) - March 7, 2012 - 45,766 - Total Cost: 23.65 (including tax)


    I dropped off my leaky radiator at a repair shop a few days ago and still haven't heard back from them. Hopefully they are repairing and testing it for free since I suspect it wasn't fixed right the first time.

    Anyway, since I drained the coolant out of the system and have no spare coolant laying around the house I decided to make the trip to Wally World to purchase 2 gallons of coolant and 2 gallons of distilled water. The stuff is sitting in the back of my Geo Metro right now, waiting for the moment it gets mixed and put into the Delorean.

  4. #114
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    I just got off the phone with the radiator shop and the thing is ready to be picked up. I think I know what I will be doing tonight. Wish me luck.

  5. #115
    Not dead yet, also Admin. sean's Avatar
    Join Date:  May 2011

    Location:  Dahlonega GA

    Posts:    2,462

    Club(s):   (SEDOC) (DCUK)

    Quote Originally Posted by stevedmc View Post
    I just got off the phone with the radiator shop and the thing is ready to be picked up. I think I know what I will be doing tonight. Wish me luck.
    Good luck supersteve!
    eBay selling at it's best I can tell you stock Delorians and quite a bit of slugs so the Turbo is a super nice up-grade.
    K-Jet: Causing electrical issues since November 5th 1955

  6. #116
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by sean View Post
    Good luck supersteve!
    Thanks. I'm going to need it since I'm hoping to spend no more than $4.50 until June.

  7. #117
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    And in June you will be glad that you don't factor fuel cost in your modest budget.
    3.0L, automatic, carbureted

  8. #118
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by Farrar View Post
    And in June you will be glad that you don't factor fuel cost in your modest budget.
    In June I will be able to afford gas because of my modest budget. People on the DML will be crying about gas like never before and I won't care.

    Frankly I don't really care about gas prices. I look at gallons, not dollars when I buy gas.

  9. #119
    Motors about after dark Michael's Avatar
    Join Date:  May 2011

    Posts:    4,922

    My VIN:    Banged your VIN'S mom

    Quote Originally Posted by stevedmc View Post
    In June I will be able to afford gas because of my modest budget. People on the DML will be crying about gas like never before and I won't care.

    Frankly I don't really care about gas prices. I look at gallons, not dollars when I buy gas.
    The number one question I get is where is the flux capacitor? The number 2 is what kind of mileage does it get? ....I never cared enough to find out either.
    http://dmctalk.org/image.php?type=sigpic&userid=90&dateline=161808992  9

  10. #120
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Well, I got the radiator mounted but it was getting too dark to finish up so I called it quits for the night. Today after work I plan to finish connecting the hoses, tighten everything, fill the system with tap water, and then pressure test and drive the thing a little bit.

    After I have verified there are no leaks, I will drain the water, blow the system out with compressed air, and then fill it up with coolant and distilled water.

    I am not putting my precious coolant in this thing until I know it is leak free.

    I do have a few concerns about their recent repair. My dad went and picked up the radiator for me and I was shocked to see how dirty it was and that they used some sort of expoxy to do part of the repair this time. I really hope the thing holds.

    The first repair looked so professional but it obviously wasn't fixed. The current repair looks so redneck. We will see if it lasts or not.
    Last edited by stevedmc; 03-15-2012 at 11:36 AM.

Page 12 of 37 FirstFirst ... 2 10 11 12 13 14 22 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •