Bill is so hardcore martyr you can never be on his side. Even he is not on his side, that is how hardcore Bill is! :eek7:
Do you typically leave the cover off over the pump like the photo a few pages back? What keeps water from collecting on top of the pump? Does this contribute to the short life you are seeing?
Attachment 3655 Attachment 3654
I'm not the one complaining about Airtex pumps. My first one did just fine until it sucked up a piece of Hervey epoxy (can't blame Airtex for that). My second pump did indeed suffer bearing failure. Based on subsequent headwind experiences (DeLoreans do catch headwind), I'm beginning to think my third one was replaced on a whim.
Bill Robertson
#5939
I've been trying for a while to get a boot cover without the nubs on the hose entry points cut off so I can keep one covered vs. having an open one where the return hose would go.
For that matter, I'd love an un-cut boot itself too...
Water from below isn't an issue. There is only slightly more than 1/4" clearance between the pump boot and the closing plate. Perhaps a drop or two might get thrown up and manage to be deflected in, but that's it.
That screen keeps my windshield plenum drain from filling the boot up. In a stroke of genius, Lotus put the plenum drain directly above the fuel pump -- gotta love British engineering.
Stock boot covers are a PITA to install, and they shrink, get hard, and split with age. You will bankrupt yourself and drive yourself crazy trying to keep a cover over the pump.
I can pop my pump in and out in seconds. I did just that at Virginia Beach to show someone my tuna can baffle. A screen is so much faster and easier -- and it works just as well.
Speaking of which, a Virginia Beach area owner is running a similar screen, with similar good results.
A New York area owner is too.
When taking your measurements, note that I cut my rubber too short and had to extend it about 1" with Gorilla tape -- the screen does not drop straight down but angles rearward slightly to clear the boot.
Bill Robertson
#5939
Bills distaste for DMCTalk moderation discussion can be continued here.
Everybody bitching and complaining about fuel pumps conveniently forgets that you can run a Bosch unit if you want -- you just need to knock the pressure down before feeding it to the carb.
That is exactly how one of my school buses is set up:
Attachment 3656
Bill Robertson
#5939
My vinyl skirt is too long or something; it doesn't quite fit right down in the gap like I thought it would.
But that's secondary to the fact that the new fuel pump as installed is too tall. I will have to figure out another solution. In case other carb users are curious about this particular fuel pump and how I manage it, I will let you know what I cobble together -- er I mean how I solve the problem. :)
Farrar
Take out these two components:
Attachment 4001
Their only purpose is to position the pickup screen lower in the tank.
Bill Robertson
#5939
Once again, I am cursed by being an early adopter.
My pipe cap is not tapped for 1/4" NPT.
There is no bushing in the pipe cap, just the close nipple, which will not come out. I've tried vise-grips and a hammer, and it won't move. Now I have a reducing coupling stuck in the bottom of the pump carrier, and that close nipple stuck in the bottom of the pipe cap.
Grr.
Farrar
There has to be something at the bottom -- a close nipple isn't long enough to go into the pump and extend all the way through the pipe cap.
Bill Robertson
#5939
I just pulled the pump out of #5939. It has a custom piece of brass tubing instead of a collection of brass fittings. I bet yours is identical.
My pipe cap is tapped 1/8 NPT. The tubing is threaded long enough to extend through the cap and into the pump.
Do you have a 1/4 NPT tap? If so, just convert your carrier into a later style (I buy the brass fittings from Lowes -- I like their barrel connectors better than McMaster's).
Bill Robertson
#5939
If anyone wants a spare, this is 1/3 of a parts house price: http://cgi.ebay.com/ebaymotors/NIEHO...item2c5eaf236e
Bill Robertson
#5939
It looks like this:
Attachment 4200
Looks just like the picture -- male on both ends. This has 1/8" NPT threads on it.
I managed to remove the coupling between it and the pickup screen, but that bit of pipe is stuck solid in that pipe cap.
Farrar
It's a custom piece of pipe. I cut the threads myself. They are at least twice as long as standard threads, to extend through the pipe cap and still grab the pump.
The pipe cap is just aluminum -- it should spin right off (unless you've managed to get a fitting stuck on the other end...).
If need be, just cut the pipe off and use the stuck fitting to spin the remaining threads out of the cap.
Bill Robertson
#5939
Totally unrelated to Farrar's fuel carrier issues:
If any Motorcraft 2100 user wants a spare, this is 1/3 of a parts house price: http://cgi.ebay.com/ebaymotors/NIEHO...item2c5eaf236e
Bill Robertson
#5939
I took off my fuel pump cover after converting and gave it away as part of my trade for an engine. Not having it may have caused my fuel pump failure, but the inside of the fuel tank did look fine upon inspection.
Anyway, I was doing some work in there today anyway and decided to install a fuel pump cover. I picked mine up at the dollar store. I believe I got a package of 25 fuel pump covers for about $2 or $3.
I reiterate: frame rail pumps are designed to get wet.
Factory design:
Attachment 4256
Aftermarket design:
Attachment 4257
I don't like water in my boot, so I rigged up a splash guard for the primary culprit (windshield plenum drain).
The argument that water is causing pump failure is a Red Herring. I think your problems are electrical. Consider this: what has failed on your pump: mechanical drive components or the electric motor itself? Both of my pump failures were mechanical (one sucked up piece of epoxy and one bearing failure), neither of which can be blamed on water exposure. My pump is grounded directly to the battery via two channels: the original frame ground and my ground bus (the frame is attached to the bus, which is itself attached directly to the battery). Electron supply is not an issue.
Bill Robertson
#5939
Just FYI, the Spectra E8012S, which is made in China and available at AutoZone, comes with female 1/8" NPT threads on the bottom for attaching a fuel pickup filter (included). The pump has a 1/4" hose barb directly on top, so there is nothing to screw in and if you mount it in the boot the hose will stick straight up, but there is enough room to close the access cover under the spare tire well. The pickup filter included with the pump also has a 1/4" hose barb. It's a perfect fit for Bill's "in-tank" solution.
The pump comes with a one-year warranty, so keep your receipt.
Farrar
Autozone uses a phone number to look up your purchase history. If Farrar and Steve know each other's phone numbers, they can coordinate purchases so there is always a pump that is less than 12 month old one of the numbers, and use it accordingly if necessary.
Bill Robertson
#5939
PEUGEOT - RENAULT - VOLVO 90 V6 ENGINE
SAE
Automotive Engineering Congress and Exposition
Francois Gastinne, Peugeot; M. Laliere, Renault; Stephen Wallman, Volvo
(Pg. 11):
FUEL INJECTION SYSTEM
Choice of system - The adoption of the continuous fuel injections (Bosch K-Jetronic) was decided upon the basis of the following major advantages:
1. Direct load sensing by the air metering device which continuously measures air flow through the engine.
2. Simple injector design since the fuel is continuously injected.
3. Fewer and simpler service requirements. Most components can be checked by a fuel pressure gauge.
4. Partial altitude compensation by the air metering device.
5. Less influence on actual air/fuel ratio by the EGR rate since actual flow is measured.
:hysterical:
Alright, saw this Delorean today...what kind of carb and intake manifold setup is this?
Carbs are Webers...just curious what vehicle the manifold and carbs came off of?
http://a3.sphotos.ak.fbcdn.net/hphot..._6456248_n.jpg
http://a6.sphotos.ak.fbcdn.net/hphot..._1450046_n.jpg
:screwy: is how the AutoZone guys respond if they know what the F150 parts are for, after you walk out the door.
:thumbup: is how DMCMW guys (and gals) respond when asking for KJet parts for a Delorean.
:rant: is what Delorians make Steve do.
:drunk: is what I have do when I visit Bill's thread(s), obviously.
:hatchet: is Bill and his Delorean.
Carbs, Italian weber 40 or 46 ;) used also on Porsche
Attachment 4739
Attachment 4738
intake are from Talbot Tagora V6 prv, the only factory 3x carb PRV, lot used by the Alpine guys... and very rare !
Attachment 4740
I checked on the price of one of those tripower set ups a year ago... IIRC they wanted $5K for the whole thing. That's a lot of money to use more gas (for a car that wasn't meant to race anyway.)
You are right...not to go on a Delorean, as was implied.
Actually, I live in Ford country and with as much as I bill there a month they love me so I rarely have to do any cross referenceing....OMG I just remembered I went back there once and found a Ford (IIRC) coolant hose that would wrap around and go behind the compressor instead of rubbing everything in sight. But I didn't use it on my D. Really, I didn't! ...I gave it and some short pipes to Ben...you can ask him.
As this thread's title clearly indicates, it is the place for asking questions about installing a carburetor on your DeLorean.
If you have ignition questions, there is a different thread devoted exclusively to that topic.
If you have EFI questions, you can either start an EFI specific thread similar to this one, or perhaps use a existing thread like Mike Lund's failed conversion thread.
K-Jet questions can be asked in the General Forum since K-Jet is not a modification.
Asking questions in the appropriate threads helps keep the forum organized.
Thank you in advance for your cooperation.
Bill Robertson
#5939
With one exception (and a diesel powered school bus) every vehicle I own is carbureted, so I can not answer EFI questions from empirical experience. If you have an EFI question, I recommend posing it to someone with practical EFI experience. If you have a carburetor question, I would be happy to answer it.
Do you have a specific carbureted vehicle in mind that you wish to discuss?
Bill Robertson
#5939