FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 4 of 5 FirstFirst ... 2 3 4 5 LastLast
Results 31 to 40 of 42

Thread: Frustrating Fuel Problem!

  1. #31
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,635

    My VIN:    03572

    Quote Originally Posted by dn010 View Post
    Also - Bill, you used 8 gauge, Dave used 10 gauge... this may be a stupid question but is there any benefit in using the one over the other in our setting? I am using 8 gauge, but I am just curious at this point... And maybe the answer will help steer future readers while doing this upgrade.
    You need to consider what voltage drop you want to tolerate.

    example:
    If you were not using the frame and only a buss wire ground, Your current from the front end is say 50 amps (headlights and fans). Now find the resistance of your buss wire using this table.

    http://www.interfacebus.com/Copper_Wire_AWG_SIze.html

    The voltage drop is equal to the resistance in ohms times the current in amps.

    So a ten foot length of AWG 8 would drop 0.32025 volts.
    Ten foot of AWG 10 would drop 0.509 volts.

    The frame of the car has a lot of "circular mils" area to conduct current. So it's pretty good even though it's made of steel. Would be interesting to test it's resistance from the battery connection to the front of the car.
    Last edited by Bitsyncmaster; 08-23-2011 at 02:44 PM.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  2. #32
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by stevedmc View Post
    I really would like to do this but don't want to fork out $200 for tools.
    I thought about using a cold chisel and a hammer, but I would probably have to blunt the chisel first in order not to cut the lugs by accident -- they're copper, so they're soft.

    Farrar
    3.0L, automatic, carbureted

  3. #33
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,635

    My VIN:    03572

    Quote Originally Posted by Farrar View Post
    I thought about using a cold chisel and a hammer, but I would probably have to blunt the chisel first in order not to cut the lugs by accident -- they're copper, so they're soft.

    Farrar
    If your going to solder the joint you don't need the best of crimpers. The crimp is needed to hold the wires and terminal together while you solder it. You definitely can't hold your hands anywhere on the wires when soldering.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  4. #34
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by Bitsyncmaster View Post
    If your going to solder the joint you don't need the best of crimpers. The crimp is needed to hold the wires and terminal together while you solder it. You definitely can't hold your hands anywhere on the wires when soldering.
    Good point.

    Here's another question: Can a soldering iron get 6 AWG cable hot enough to solder a lug on all the way around, or should I get a torch and plan on extinguishing the burning insulation later?

    Farrar
    3.0L, automatic, carbureted

  5. #35
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    The way I'd like to complete this task will require both the torch/solder and crimp tool.

    Before I got my crimp tool, I went out and got a $10 nut splitter and smoothed over the splitting wedge (these things never work right anyway). Then use 2 bolts or something on either side of the bottom to make a "U" shape for the connector (I made a steel U shaped base for mine to put the connectors in, put the connector in the splitter and then run the wire in it - n crank 'er down!

  6. #36
    Senior Member AdmiralSenn's Avatar
    Join Date:  May 2011

    Posts:    443

    I was actually able to crimp my 4ga connectors with a regular handheld wire crimper/stripper combo tool. Took some force but I got four crimps into it, two per side, then used a torch + solder to finish it off. So if you're willing to really crank and lean on a handheld tool, it will work in a pinch.

  7. #37
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,635

    My VIN:    03572

    Quote Originally Posted by Farrar View Post
    Good point.

    Here's another question: Can a soldering iron get 6 AWG cable hot enough to solder a lug on all the way around, or should I get a torch and plan on extinguishing the burning insulation later?

    Farrar
    Get a big iron or solder gun. You want at least a 100 watts or more. The higher power will solder it faster and do less damage to the insulation on the wires.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  8. #38
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    Get lugs with closed end connections - heat the connector with a torch and fill it with solder, then while the solder is still molten you put the wire in the lug. Use common sense though - the solder will overflow and burn whatever is underneath it so put the lug in a vice or something. If you have smaller crimp tool and need that extra force to crimp - put them in a vice and use the vice to give the extra force - again, common sense...don't go all out or your tool will break down.

  9. #39
    EFI'd dn010's Avatar
    Join Date:  Jul 2011

    Location:  Florida: Pinellas County

    Posts:    2,395

    My VIN:    5003 Never placed Concourse 2002-Current

    Club(s):   (DCF)

    Quote Originally Posted by stevedmc View Post
    Ouch, that sounds like an expensive tool for doing such a cheap job. I really would like to do this but don't want to fork out $200 for tools. I have a feeling someone could make a nice chunk of change selling kits for this.

    I'd offer to make some of these grounds, but this wasn't my idea so it would be up to Bill and Dave, etc. If no one wants to make them - then I'll attempt.

  10. #40
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Quote Originally Posted by dn010 View Post
    Also - Bill, you used 8 gauge
    No, Bill used 4 gauge. They are regular battery cables. I used four 60 inch cables IIRC. Some of the ring terminals that came on the cables were left in place, and some new ones were added (parts house sells those too). The terminal on my radiator bracket was obviously added by me, as were the terminals on the bulkhead bolt, the engine block:
    GroundBusEngine.jpg
    and the terminals that connect the bus together by the radio bracket (not pictured). Anything smaller than 3/8" was done by me. There's nothing to it. Drill a little hole for the solder to flow through, flux the inside of the terminal, stick the cable in it, heat them both up with a plumber's torch, then flow the solder in. It's no different than sweating pipe.

    I'm getting ready to run a few errands -- I'll take The Worlds Cheapest Digital Camera with me to snap a pic of the terminal lungs at Lowes.

    Bill Robertson
    #5939

Page 4 of 5 FirstFirst ... 2 3 4 5 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •