FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 62 of 77 FirstFirst ... 12 52 60 61 62 63 64 72 ... LastLast
Results 611 to 620 of 763

Thread: Ask Bill about carbing a DeLorean and other K-Jet/Carb tangets

  1. #611
    Senior Member DMCVegas's Avatar
    Join Date:  Oct 2011

    Location:  Las Vegas

    Posts:    2,507

    My VIN:    6585

    Quote Originally Posted by stevedmc View Post
    I am proud to say I drove a total of 1278 miles since Friday. My car made it to Sean's house, and then Ron's (way up in the mountains with a tuna fish can baffle) and all the way back down to my house without a single fuel delivery problem at all
    Out of curiosity, when you get a chance can you pull the gray plug on your Intertia Switch and check to see if it's in good shape?

  2. #612
    Rick/AKA.. DA BEARD congerz83's Avatar
    Join Date:  May 2011

    Location:  Congers NY

    Posts:    188

    My VIN:    SCEDT26T5BD06996

    Club(s):   (DMA)

    Quote Originally Posted by Ron View Post
    pat the peddle
    I really need to apply maximum force as fast as I can to get the RPM to drop. Sometimes it actually takes 7-8 times to accomplish this. I'm afraid I'm going to put my foot through the floor.

    Ok so the car sat since 4pm yesterday. I did NOT get a chance to adjust the carb yesterday. I figured I just give the update on today's behavior. It was a bit chilly this morning in the tri-state area. Pumped pedal twice, turned on, the car stayed on at regular "choke-less" idle without stalling. Let it run until I was ready to leave for work (10MIN). The car ran very well, but again, rpm shot up to 2000RPM once I got 1 mile down the road to the first traffic light. It's stayed like that through out most of the 15MIN ride to work.
    "He that hath a beard is more than a youth, and he that hath no beard is less than a man"
    - William Shakespeare

  3. #613
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by congerz83 View Post
    Pumped pedal twice,
    You should not have to "pump the pedal." Just touch the pedal until you hear the choke plates reset, then take your foot off the pedal and turn the key. If the car has only been sitting a day or so, there will still be plenty of fuel in the bowl.

    Farrar
    3.0L, automatic, carbureted

  4. #614
    Senior Member Ashyukun's Avatar
    Join Date:  Jun 2011

    Location:  Lexington, KY

    Posts:    242

    My VIN:    16655

    Quote Originally Posted by congerz83 View Post
    I also have an idle problem... as well as an acceleration problem and a cold start problem... but I digress. My car will idle high when first started then go back to normal. Then, even after warm, it'll idle at about 2,000RPM until I punch the gas quickly. I'm guessing this has something to do with the choke. Also, at times, after awhile of driving, the car will idle very low 450-500RPM it will also stall at times in during this "mode" of operation. I'm also going to start keeping better track of my mileage because I think mine has dropped drasticly.

    Also the car bogs down upon acceleration VERY heavily when you first start the car. Even during normal operation I cannot floor the accelerator without heavy "bucking" This carb conversion only has about 300miles since installation. I also changed the plugs shortly after the conversion.
    It sounds a LOT like you're having the same issues that I am. I've largely traced the problem down to a potential combination of two things: the electric choke not behaving properly and opening the choke plates as it's supposed to, and the fast idle cam 'resetting' and interfering with the normal operation of the throttle plates via the throttle.

    I don't know exactly WHY it's doing this (or whether it's related to the potential issue with the choke), but as I understand it the fast idle is supposed to kick down after you 'bump' the throttle to get the throttle off the fast idle cam. On mine, every time I let the throttle go back to idle, it resets the fast idle cam and bumps the idle back up to around 2,000- and also wants to climb higher continually. If I'm standing there working the linkages by hand, I can pull on the throttle and the push down on the fast idle assembly/choke and it will pop to where it's supposed to be for normal running. If I don't let the throttle all the way back to idle, it will run the way it's supposed to- but if I let go of the throttle, it will pop the choke closed and reset the fast idle cam. I'm planning on pulling off the carb to test the choke and go through the procedure for setting the fast idle cam- though I don't know how it could have gotten messed up since I've not touched any of the adjustments on it.

    As for your issue with the low idle, is that with nothing (A/C, fans, stereo, lights) running or with a lot of other engine loads running? At the beginning of the summer I had a similar problem when I started driving at night when I needed the A/C on- in the 'stock' setup, our carbs don't have any kind of mechanism to bump the idle up to account for loads like the A/C and headlights so if the idle is set without the engine being loaded when everything is turned on it can drag the idle down a lot. It may just be that you need to raise the idle a bit so with everything off it idles a bit high but then idles normally with what you're usually using turned on.

  5. #615
    Administrator Ron's Avatar
    Join Date:  Jun 2011

    Location:  North GA

    Posts:    6,200

    Club(s):   (SEDOC) (DCUK)

    Quote Originally Posted by stevedmc View Post
    Float instructions are silly anyway. Just set the float to a reasonably level and the shut off valve will do its job.
    Hmmm...Why do you think that the settings are often down to the 1/64" then? There is more going on than keeping it from over flowing and not running out of gas on long full throttle runs...

    Quote Originally Posted by congerz83 View Post
    I really need to apply maximum force as fast as I can to get the RPM to drop. Sometimes it actually takes 7-8 times to accomplish this. I'm afraid I'm going to put my foot through the floor.

    Ok so the car sat since 4pm yesterday. I did NOT get a chance to adjust the carb yesterday. I figured I just give the update on today's behavior. It was a bit chilly this morning in the tri-state area. Pumped pedal twice, turned on, the car stayed on at regular "choke-less" idle without stalling. Let it run until I was ready to leave for work (10MIN). The car ran very well, but again, rpm shot up to 2000RPM once I got 1 mile down the road to the first traffic light. It's stayed like that through out most of the 15MIN ride to work.
    It's easy to miss the fork when installing the choke spring and it is possible on some 2100s to flip the choke spring making it work backwards (when you look at it installed in the cap, IIRC it should be wound clockwise (looks like a 6). Could explain a lot of your problems.??? ... check this when you do the things mentioned earlier. (Also, hold the throttle 1/2 open and turn the key on and see if the choke starts off ~closed and slowly opens fully, be patient...)
    If at ANY time the choke plate is floppy, the spring has missed the fork.

    Quote Originally Posted by Farrar View Post
    You should not have to "pump the pedal." Just touch the pedal until you hear the choke plates reset, then take your foot off the pedal and turn the key. If the car has only been sitting a day or so, there will still be plenty of fuel in the bowl.
    +1/2 ;-)

    Once fully on a cold engine is what every owners manual I have ever seen said (for "dumb" carburetors...primes the engine...and purges the pump)...more on cold days. Perhaps yours is running rich and/or it's been a lot warmer there???

  6. #616
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by Ron View Post
    Perhaps yours is running rich and/or it's been a lot warmer there???
    I live in southeast Louisiana; it's always a lot warmer here.

    Farrar
    3.0L, automatic, carbureted

  7. #617
    Rick/AKA.. DA BEARD congerz83's Avatar
    Join Date:  May 2011

    Location:  Congers NY

    Posts:    188

    My VIN:    SCEDT26T5BD06996

    Club(s):   (DMA)

    Quote Originally Posted by Ashyukun View Post
    As for your issue with the low idle, is that with nothing (A/C, fans, stereo, lights) running or with a lot of other engine loads running?
    This happens no matter what else I'm running. To tell the truth, it's the least common issue I have. The most common times it happens is at start-up. Usually after I've been driving for a while, and I stop to pick something up, and start the car again. But then again after 8 hours of sitting it started and ran in that 500rpm range for about a minute.
    "He that hath a beard is more than a youth, and he that hath no beard is less than a man"
    - William Shakespeare

  8. #618
    Rick/AKA.. DA BEARD congerz83's Avatar
    Join Date:  May 2011

    Location:  Congers NY

    Posts:    188

    My VIN:    SCEDT26T5BD06996

    Club(s):   (DMA)

    I have had the new fuel pump in for about 500 miles with no problem. I can't believe I'm actually impressed by that statement. My question is, where to I get the metal "cup" that the pump screws into with the filter on the other side? Is that a custom made "Bill Part?"
    "He that hath a beard is more than a youth, and he that hath no beard is less than a man"
    - William Shakespeare

  9. #619
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Bill makes those "fuel pump carriers" from aluminum 2" NPT pipe and pipe cap. He drills and taps threads for a coupler in the middle of the cap, so that you can screw the pickup filter onto one end of the coupler and the pump onto the other.

    Farrar
    3.0L, automatic, carbureted

  10. #620
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Merry Christmas Bill.

Page 62 of 77 FirstFirst ... 12 52 60 61 62 63 64 72 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •