FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 44 of 111 FirstFirst ... 34 42 43 44 45 46 54 94 ... LastLast
Results 431 to 440 of 1102

Thread: Farrar's car blog

  1. #431
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    I'm sure your needle valve is fine. If you have any doubt, energize the pump and see if fuel flow is shut off. If it is, your tip is fine.

    That is one advantage of electric fuel pumps over mechanical pumps.

    Bill Robertson
    #5939

  2. #432
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    The needle valve is fine.

    So are all of my O-rings and vacuum lines.

    I have spark on all six cylinders.

    Still runs like crap.

    Suggestions?

    Edit: On second thought, you can make suggestions but I will simply add them to a to-do list. I am not going to do anything to the car until I have a nice long chunk of time to work on it. I am going to take a DeLorean vacation and concentrate on school and work, for now.

    Farrar
    Last edited by Farrar; 09-21-2011 at 10:13 PM.
    3.0L, automatic, carbureted

  3. #433
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    If you are 100% sure your intake is vacuum tight (that includes HVAC/brake booster and modulator valve. Also make sure whatever you are using in the injector bungs is vacuum tight), this is an instance where you need to use the curb idle screw.

    Reseat the idle screws all the way. Use the curb idle screw to crack the throttle plates open enough for the engine to run. While it's warming up, use a timing light to ensure all 6 plugs are firing consistently.

    When the engine is warm, alternate between opening the idle screws and closing the throttle plates. Open each idle screw about 1/2 turn, then try backing off the curb idle screw. It shouldn't take long for you to find idle screw settings that allow the engine to idle smoothly with the throttle plates fully closed (curb idle screw not touching at all) -- about 1.5 to 2 turns. 3.5 turns is way too far -- something is definitely wrong there. I just double checked mine -- just shy of 2 turns each.

    If you haven't touched the fast idle screw or rotated the choke housing, you should be all set for a cold start tomorrow.

    Bill Robertson
    #5939

  4. #434
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by content22207 View Post
    If you are 100% sure your intake is vacuum tight (that includes HVAC/brake booster and modulator valve. Also make sure whatever you are using in the injector bungs is vacuum tight), this is an instance where you need to use the curb idle screw.
    I have always used the curb idle screw...
    3.0L, automatic, carbureted

  5. #435
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    Quote Originally Posted by Farrar View Post
    Still runs like crap.

    Suggestions?
    We could just meet up and swap carbs/manifolds for testing purposes. If your car still runs like crap your issue lies somewhere else.

    Edit: I'm going to be in Laplace tomorrow after work. If you have time then we could meet up and swap stuff in a parking lot somewhere.
    Last edited by stevedmc; 09-22-2011 at 02:49 PM.

  6. #436
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by stevedmc View Post
    I'm going to be in Laplace tomorrow after work. If you have time then we could meet up and swap stuff in a parking lot somewhere.
    No time for that tomorrow, but I appreciate the offer.

    Farrar
    3.0L, automatic, carbureted

  7. #437
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    I just had an interesting thought: every time I spend money on an area of the car, I have trouble in another area. Perhaps I should simply avoid spending money on any upgrades or improvements of any kind, instead simply waiting until things break and replacing them as needed.

    Ah, well. The vacation continues. (Although I will have to move it to a different parking spot soon.) Easy enough not to spend money on it when I'm not driving it.

    Farrar
    3.0L, automatic, carbureted

  8. #438
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    Have you ensured your HVAC/brake booster line is vaccum tight? Last year Matt Spittle's HVAC supply line cracked underneath the console, just as mine did in 2003. Use your hand held vacuum pump to ensure both lines hold vacuum (pull it off the manifold and test it there).

    Also test your modulator valve while you're at it.

    Bill Robertson
    #5939

  9. #439
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Is the "modulator valve" the thing behind the HVAC selector switch with all the different vacuum lines for the air flaps connected to it?

    Farrar
    3.0L, automatic, carbureted

  10. #440
    Banned
    Join Date:  Jun 2011

    Posts:    1,068

    It's the vacuum operated valve on the transmission that keeps it from shifting like a 1952 Mack truck -- the other 3/16" line off the back of your manifold.

    Bill Robertson
    #5939

Page 44 of 111 FirstFirst ... 34 42 43 44 45 46 54 94 ... LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •