FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Results 1 to 10 of 52

Thread: Efi?

Threaded View

Previous Post Previous Post   Next Post Next Post
  1. #22
    Senior Member AdmiralSenn's Avatar
    Join Date:  May 2011

    Posts:    443

    I will agree that the engine access is SUPER EASY now. Far fewer wires, far fewer hoses and everything is easily accessible right there - in my case I have to do a little extra work to get to the spark plugs because of the way I mounted my fuel rails, but it's overall less annoying than the K-Jet injectors - I just undo the fuel rail bolts and pop the rail out. Super easy.

    As far as the varying installation choices, there are lots of factors that explain why each setup is different. In my case, I had a car that the previous owner had converted to a 3.0 - not an Eagle motor, he had the odd-fire enlarged internally... don't ask. It was very nearly a completely different motor. I'm running Daryl's tune because he had almost the same size fuel injectors (and is also using the stock manifold) but I had to tweak it a good deal to get it running smoothly and not run crazy rich or lean. I figured why replace a bunch of functional components simply to line up with everyone else's builds, when my tune was going to be so wildly different and I couldn't really afford the extra parts anyway? And not everyone has easy access to variant PRV parts, either.

    EFI is also nice because you have the option to pursue higher performance builds later. My car came with a nitrous oxide kit that I'll be reinstalling once I replace the fire-damaged components (and once I get Christine completely road-worthy again, of course...). I can monitor the engine and force the nitrous system to shut off under certain conditions (e.g. it won't actuate under a certain throttle percentage, or outside of a specific temperature range, etc). This makes it a lot safer than the NOS + K-Jet system that the car came with, which had no provision to check for a dangerous lean condition, for example. The vast array of wires that controlled the system previously will be completely gone - all the wires I need are already run for the EFI controller, and I can just tap the controller triggers into the MS outputs without needing to re-run everything.

    It can be a VERY rewarding and fun experience, and I'd highly recommend it if you're willing to tackle a fairly involved project and learn a great deal. #3416 runs FAR FAR FAR better on EFI, even on a rough tune, than it ever did on K-Jet.

    Quote Originally Posted by content22207 View Post
    Why doesn't an EFI user with the original K-Jet manifold at least document his conversion? For an EFI kit to work with the masses, it will need to use a readily available intake manifold. That is why I make my own (I need a dependable supply of intake manifolds. For centralized fuel metering the K-Jet manifold is very difficult to work with, although Byrne Heninger has come up with a way to do it, and a welder who can work with cast aluminum).

    Bill Robertson
    #5939
    Bill, I haven't fully documented mine because it really isn't that different from anyone else's, fundamentally - the ECU and wiring are virtually identical, and those are really the difficult parts. And hardly anyone ever uses the original manifold as there are some good reasons to switch to a factory EFI unit - built in idle control, easier TPS adaptation, better fuel atomization compared to the K-Jet injector holes, and overall a lot less head-scratching and fabrication. The 2.8 EFI manifold is a LOT closer to drop-in than the factory unit - witness how fast Owen went from bare engine to fully running EFI with idle, spark advance, and everything else, compared to my ongoing work. I still don't have idle control or spark control yet because I keep having to fiddle with throttle sensor and air intake issues (though I did just recently solve the intake problem).

    I would LOVE to make a production run of conversion parts for the factory manifold (throttle sensor mounts, idle and emissions port manifolds, etc) but I just don't have the time or resources to make it happen. Plus I haven't hammered out the issues with, you know, making them actually work yet.
    Last edited by AdmiralSenn; 09-21-2011 at 11:34 PM.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •