FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 956 of 957 FirstFirst ... 456 856 906 946 954 955 956 957 LastLast
Results 9,551 to 9,560 of 9562

Thread: What have you done to your DeLorean today?

  1. #9551
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,644

    My VIN:    03572

    I'm now guessing the problem with my blinkers is the flasher relay. I did not think of this before but the indicator lamps were incandescent and now just draw 5 ma. I had bought an LED flasher back when I put LEDs in the front and back signals. But it may not be good enough now there are no incandescent bulbs. It must be right on the edge of working because the 4 way flashers work which puts more LED loads on it. I was looking for an incandescent bulb to test this theory but could not find one in my junk draws.

    I'll just buy another flasher.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  2. #9552
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,644

    My VIN:    03572

    Quote Originally Posted by mike123 View Post
    Fuel gauge at 6:00 seems to most commonly be due to the needle getting stuck. On my car it seems to happen when I'm at 1/2 tank or less. I can tap on the binnacle a bit to jostle it back to being driven by the electrical signal, but as soon as I shut off the car and turn it back on again, it will go back to being stuck at 6:00. If I stay above 1/2 tank, it doesn't get stuck.

    I'm planning to install pin stop on the gauge this winter, unless I open it up and see some obvious gunk that I can clear off to fix it.
    You are correct. It was just stuck (does need stops). What I did was pull out the binnacle and put 12 volts on the power pin and the gauge did not move (It should show 12:00) with power and no sensor load). I had to bang on the binnacle pretty hard to get it to fly to 12:00. I put the binnacle back in the car and now the gauge is working. So I guess my gauge does not get stuck at 12:00.

    I really should put a pin stop on it now that the binnacle is out, but I'm getting tired of working on it.

    If your gauge gets stuck at 6:00 it may help to open the sensor connection and then the voltage is working with more force on the gauge.
    Last edited by Bitsyncmaster; 11-16-2026 at 10:49 AM.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  3. #9553
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,644

    My VIN:    03572

    Quote Originally Posted by mike123 View Post
    Fuel gauge at 6:00 seems to most commonly be due to the needle getting stuck. On my car it seems to happen when I'm at 1/2 tank or less. I can tap on the binnacle a bit to jostle it back to being driven by the electrical signal, but as soon as I shut off the car and turn it back on again, it will go back to being stuck at 6:00. If I stay above 1/2 tank, it doesn't get stuck.

    I'm planning to install pin stop on the gauge this winter, unless I open it up and see some obvious gunk that I can clear off to fix it.
    I'm guessing your running the OEM sender because that would drive both fuel gauge coils at the same time on key on. If you have a capacitor on your sender that would be worse.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  4. #9554
    Senior Member
    Join Date:  Nov 2022

    Posts:    150

    My VIN:    7012

    Quote Originally Posted by Bitsyncmaster View Post
    I'm guessing your running the OEM sender because that would drive both fuel gauge coils at the same time on key on. If you have a capacitor on your sender that would be worse.
    It's actually the integrated fuel pump with sender from one of the DMC vendors. I don't know anything about it though; I had it professionally installed.

    That makes sense on giving it the full 12 volts for a little extra 'oomph'. Thankfully it doesn't get stuck too hard right now, and a few light taps on the top or bottom of the binnacle will nudge it back into free movement. I'm going to pull the binnacle this winter and see if I can clean it out and/or build in a little pin stops. I am also going to switch to a BTTF-style speedometer decal if I can get one made that looks close enough to the stock face. I get really nervous with these needles though; they just seem so delicate, so I've been procrastinating both of these updates!

  5. #9555
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,644

    My VIN:    03572

    Quote Originally Posted by mike123 View Post
    It's actually the integrated fuel pump with sender from one of the DMC vendors. I don't know anything about it though; I had it professionally installed.

    That makes sense on giving it the full 12 volts for a little extra 'oomph'. Thankfully it doesn't get stuck too hard right now, and a few light taps on the top or bottom of the binnacle will nudge it back into free movement. I'm going to pull the binnacle this winter and see if I can clean it out and/or build in a little pin stops. I am also going to switch to a BTTF-style speedometer decal if I can get one made that looks close enough to the stock face. I get really nervous with these needles though; they just seem so delicate, so I've been procrastinating both of these updates!
    I've been thinking of how to put a stop on it. Only thing I can think of is to 3D print a stop (resin print) and somehow glue it on the face. I guess you could glue a clear stop on the front plexiglass panel but would be hard to align where if goes.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  6. #9556
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,644

    My VIN:    03572

    Here is a photo of my illumination with LEDs. This is daytime in the garage with the lights off. I think I will PWM it to be able to adjust the brightness.
    Attached Images
    Dave M vin 03572
    http://dm-eng.weebly.com/

  7. #9557
    Senior Member
    Join Date:  Nov 2022

    Posts:    150

    My VIN:    7012

    User dn010 posted some pictures of pins he drilled holes for and put in, here: https://dmctalk.org/showthread.php?1...l=1#post286062

    I was thinking rather than metal or painted metal, I could use a black abs plastic rod and 3D print a little black ring "bezel" to slide around it. And I am hoping I could access the backside of the gauge face to glue from that side, but sounds like maybe not. Looking forward to figuring something out though, and I'll definitely post pictures if I come up with anything I am happy with.

  8. #9558
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,644

    My VIN:    03572

    Quote Originally Posted by mike123 View Post
    User dn010 posted some pictures of pins he drilled holes for and put in, here: https://dmctalk.org/showthread.php?1...l=1#post286062

    I was thinking rather than metal or painted metal, I could use a black abs plastic rod and 3D print a little black ring "bezel" to slide around it. And I am hoping I could access the backside of the gauge face to glue from that side, but sounds like maybe not. Looking forward to figuring something out though, and I'll definitely post pictures if I come up with anything I am happy with.
    I have a spare gauge and it looks like you can pull the black plastic face off but you would have to remove the needles. Then you would have to install the needles back in the same location. Really to risky to get it done right. I think installing on the front side is the only option.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  9. #9559
    Senior Member Bitsyncmaster's Avatar
    Join Date:  May 2011

    Location:  Leonardtown, MD

    Posts:    9,644

    My VIN:    03572

    Quote Originally Posted by Bitsyncmaster View Post
    Here is a photo of my illumination with LEDs. This is daytime in the garage with the lights off. I think I will PWM it to be able to adjust the brightness.
    I layed out a PWM circuit board. Still not sure if it is needed. But I've always been thinking of using PWM for the blower motor so this unit probably can take that current. I may order some PCBs just to play with that. Doing the blower motor would eliminate the two blower relays and blower resistor pack.
    Dave M vin 03572
    http://dm-eng.weebly.com/

  10. #9560
    Senior Member - Owner since 2003 Patrick C's Avatar
    Join Date:  May 2011

    Location:  Northern Michigan

    Posts:    1,239

    My VIN:    1880

    Club(s):   (DCO) (DCUK)

    Quote Originally Posted by Bitsyncmaster View Post
    Here is a photo of my illumination with LEDs. This is daytime in the garage with the lights off. I think I will PWM it to be able to adjust the brightness.
    Cliff Schmucker gave me one of these probably 15 years ago to replace the rheostat and it controls the binnacle LEDs nicely. As I recall we did a wrap of electrical tape around the stem so the stock plastic knob fits tight.

    https://www.mouser.com/en/ProductDet...g7JAaxrw%3D%3D
    Patrick C.
    VIN 1880

Page 956 of 957 FirstFirst ... 456 856 906 946 954 955 956 957 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •