FRAMING JOHN DELOREAN - ON VOD www.framingjohndeloreanfilm.com
Page 91 of 111 FirstFirst ... 41 81 89 90 91 92 93 101 ... LastLast
Results 901 to 910 of 1102

Thread: Farrar's car blog

  1. #901
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by Ron View Post
    Sounds like the choke is set wrong to me... Are you setting it with the throttle held ~half open and the engine DEAD cold (as in has sat ALL night)?
    I haven't done that in a while, but yes, that is how I set it.

    Although the engine idles like crap when started cold, it idles even worse when started hot.
    3.0L, automatic, carbureted

  2. #902
    Senior Member AdmiralSenn's Avatar
    Join Date:  May 2011

    Posts:    443

    Quote Originally Posted by Farrar View Post
    Wow, nice troubleshooting procedure, Dennis! Thanks! I will get to that this weekend if I can.

    In other news, I've often heard that the back plate for the Sanden SD508 (and SD5H14 for R-134) compressors was unavailable. Well, I found something a while ago which looks awfully familiar... correct me if I'm wrong, somebody, but isn't this it?
    It says it's a 5-bolt Q head, so unless it's listed wrong, yes, that is our compressor head. Nice find!
    Aka Adam S, aka Adam Wright
    1981 DMC-12 #3416, mothballed in preparation for motor swap
    2006 Volvo S60R

  3. #903
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by AdmiralSenn View Post
    It says it's a 5-bolt Q head, so unless it's listed wrong, yes, that is our compressor head. Nice find!
    Thanks! I actually ran across it while looking for HVAC vents. I just happened to poke around because I saw they sold replacement parts for GM AC systems, and there it was
    3.0L, automatic, carbureted

  4. #904
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quick question: how difficult is it to replace the sway bar bushings and brackets? My brackets are scratched from when the car was lowered (too much) and I would like to replace the parts in that area with Toby's kit. Do I have to watch out for springy suspension parts? Should I raise the car on jack-stands or ramps?

    I am mentioning this because on another thread someone mentioned annoying front-end vibration at speed which was cured by installation of Toby's sway bar hardware kit. My car has pretty much always had that symptom so I was thinking of trying that solution. The rubber could stand to be replaced regardless.

    Thanks in advance!
    3.0L, automatic, carbureted

  5. #905
    My friends think I'm nuts jawn101's Avatar
    Join Date:  May 2011

    Location:  Sacramento-ish

    Posts:    4,408

    My VIN:    02100

    Club(s):   (NCDMC) (DCUK)

    Quote Originally Posted by Farrar View Post
    Quick question: how difficult is it to replace the sway bar bushings and brackets? My brackets are scratched from when the car was lowered (too much) and I would like to replace the parts in that area with Toby's kit. Do I have to watch out for springy suspension parts? Should I raise the car on jack-stands or ramps?

    I am mentioning this because on another thread someone mentioned annoying front-end vibration at speed which was cured by installation of Toby's sway bar hardware kit. My car has pretty much always had that symptom so I was thinking of trying that solution. The rubber could stand to be replaced regardless.

    Thanks in advance!
    Easy. All you need is a wrench and for the car to be high enough for you to get under it. The sway bar will drop down about 4" when released from the crumple tube, so don't get wanged in the head by it. It's easy enough to move back into position by hand but I used a floor jack to help keep it in place while I put the brackets back on so I'd have both hands free. Not hard though.
    Jon
    1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
    restoration log, March 2011 to present
    full and detailed photo restoration log

  6. #906
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Thanks, Jon!
    3.0L, automatic, carbureted

  7. #907
    My friends think I'm nuts jawn101's Avatar
    Join Date:  May 2011

    Location:  Sacramento-ish

    Posts:    4,408

    My VIN:    02100

    Club(s):   (NCDMC) (DCUK)

    Quote Originally Posted by Farrar View Post
    Thanks, Jon!
    No prob It isn't any harder to do the bushings for the sway bar in the LCAs at the same time, so if you are feeling like those need to be done this is a good time. Or if you wanna paint your sway bar (I sure as hell do!)
    Jon
    1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
    restoration log, March 2011 to present
    full and detailed photo restoration log

  8. #908
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Today, I got back to the problem of the engine not starting with the key.

    When I re-wired the relay sockets, I put everything back the way I found it. But the Start Inhibit Relay does not seem to be wired as indicated in the diagram.

    Note that I never had problems starting the car with the key until about two years ago, and it was only intermittent. Now it's almost constant -- in fact, the last several times I tried to start the engine, I had to do so from the engine compartment, so I think it's valid to say that it's now a consistent problem.

    I confirmed continuity to ground through the neutral safety switch. I confirmed good connections on the brown wire (terminal 30) and the yellow/white wire (one of the coil terminals, I can't remember which).

    Edit: I also swapped out the relay with a known good relay to no effect.

    What I cannot, at the moment, confirm, is either of the other two wires. One red/white wire has a length added onto it of plain white wire; looks like someone clipped it too short by accident and then just added a few inches to make it fit. But then instead of a second red/white wire, I have a blue wire which disappears behind the rear parcel shelf wall. What would appear to be the second red wire terminates in a wire nut underneath the relays, and it has been there ever since I bought the car in 2007.

    When I put my meter between the red/white wire in the socket and ground, and turn the key, I get no reading.

    When I put my meter between the orphaned red/white wire and ground, and turn the key, I get no reading.

    Leaving that aside, I decided to just start the engine from the engine compartment and, with every vacuum port but PCV blocked (also excepting one port for a vacuum gauge) I fired 'er up. Still idles like shit. I saw what looked like water in the carburetor chimneys, so I revved up the engine and sprayed some carburetor cleaner down its throat, but that only helped it run smoother for a few seconds. When it settles back into idle, it misses so badly that it jostles me as I sit in the seat.

    I took some video of the entire process, but it will be a while before YouTube processes it. (Just wait until you see the vacuum gauge -- worst vacuum readings I have ever seen!)

    In the meantime, I guess I am going to have to cancel my DCS registration. It looks like Sparky won't be reliable any time soon.
    3.0L, automatic, carbureted

  9. #909
    Banned
    Join Date:  May 2011

    Location:  Baton Rouge, Louisiana

    Posts:    3,047

    My VIN:    16510 and carbureted

    Club(s):   (GCD) (SEDOC) (DCUK)

    How about I come over after work one night this week and see what I can do? I'm curious how the car would idle if I were to put my carb and manifold on your car. Have you checked your spark plugs? We could swap ignition modules too and see what happens.

    I forgot to mention but I have an ulterior motive to get your car ready for DCS. I really don't want to be alone with Bill for 3 nights. I'm not sure I would survive.

  10. #910
    Owner since 2007 Farrar's Avatar
    Join Date:  May 2011

    Location:  Fort Lauderdale

    Posts:    4,740

    My VIN:    02613

    Club(s):   (DCF)

    Quote Originally Posted by stevedmc View Post
    How about I come over after work one night this week and see what I can do? I'm curious how the car would idle if I were to put my carb and manifold on your car. Have you checked your spark plugs? We could swap ignition modules too and see what happens.
    Your carb and manifold would be steaming hot after that 90-minute drive! I am not sure I could operate on anything that hot... usually, I let the engine sit overnight if I am to work on it.

    Quote Originally Posted by stevedmc View Post
    I forgot to mention but I have an ulterior motive to get your car ready for DCS. I really don't want to be alone with Bill for 3 nights. I'm not sure I would survive.
    Bill doesn't like me anymore... I might have to room with someone else anyway.
    3.0L, automatic, carbureted

Page 91 of 111 FirstFirst ... 41 81 89 90 91 92 93 101 ... LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •