Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
Quick question: how difficult is it to replace the sway bar bushings and brackets? My brackets are scratched from when the car was lowered (too much) and I would like to replace the parts in that area with Toby's kit. Do I have to watch out for springy suspension parts? Should I raise the car on jack-stands or ramps?
I am mentioning this because on another thread someone mentioned annoying front-end vibration at speed which was cured by installation of Toby's sway bar hardware kit. My car has pretty much always had that symptom so I was thinking of trying that solution. The rubber could stand to be replaced regardless.
Thanks in advance!
3.0L, automatic, carbureted
Location: Sacramento-ish
Posts: 4,408
My VIN: 02100
Club(s): (NCDMC) (DCUK)
Easy. All you need is a wrench and for the car to be high enough for you to get under it. The sway bar will drop down about 4" when released from the crumple tube, so don't get wanged in the head by it. It's easy enough to move back into position by hand but I used a floor jack to help keep it in place while I put the brackets back on so I'd have both hands free. Not hard though.
Jon
1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
restoration log, March 2011 to present
full and detailed photo restoration log
Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
Thanks, Jon!
3.0L, automatic, carbureted
Location: Sacramento-ish
Posts: 4,408
My VIN: 02100
Club(s): (NCDMC) (DCUK)
Jon
1981 DMC-12 #02100. July 1981. 5-speed, black, grooved w/flap.
restoration log, March 2011 to present
full and detailed photo restoration log
Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
Today, I got back to the problem of the engine not starting with the key.
When I re-wired the relay sockets, I put everything back the way I found it. But the Start Inhibit Relay does not seem to be wired as indicated in the diagram.
Note that I never had problems starting the car with the key until about two years ago, and it was only intermittent. Now it's almost constant -- in fact, the last several times I tried to start the engine, I had to do so from the engine compartment, so I think it's valid to say that it's now a consistent problem.
I confirmed continuity to ground through the neutral safety switch. I confirmed good connections on the brown wire (terminal 30) and the yellow/white wire (one of the coil terminals, I can't remember which).
Edit: I also swapped out the relay with a known good relay to no effect.
What I cannot, at the moment, confirm, is either of the other two wires. One red/white wire has a length added onto it of plain white wire; looks like someone clipped it too short by accident and then just added a few inches to make it fit. But then instead of a second red/white wire, I have a blue wire which disappears behind the rear parcel shelf wall. What would appear to be the second red wire terminates in a wire nut underneath the relays, and it has been there ever since I bought the car in 2007.
When I put my meter between the red/white wire in the socket and ground, and turn the key, I get no reading.
When I put my meter between the orphaned red/white wire and ground, and turn the key, I get no reading.
Leaving that aside, I decided to just start the engine from the engine compartment and, with every vacuum port but PCV blocked (also excepting one port for a vacuum gauge) I fired 'er up. Still idles like shit. I saw what looked like water in the carburetor chimneys, so I revved up the engine and sprayed some carburetor cleaner down its throat, but that only helped it run smoother for a few seconds. When it settles back into idle, it misses so badly that it jostles me as I sit in the seat.
I took some video of the entire process, but it will be a while before YouTube processes it. (Just wait until you see the vacuum gauge -- worst vacuum readings I have ever seen!)
In the meantime, I guess I am going to have to cancel my DCS registration. It looks like Sparky won't be reliable any time soon.
3.0L, automatic, carbureted
Location: Baton Rouge, Louisiana
Posts: 3,047
My VIN: 16510 and carbureted
Club(s): (GCD) (SEDOC) (DCUK)
How about I come over after work one night this week and see what I can do? I'm curious how the car would idle if I were to put my carb and manifold on your car. Have you checked your spark plugs? We could swap ignition modules too and see what happens.
I forgot to mention but I have an ulterior motive to get your car ready for DCS. I really don't want to be alone with Bill for 3 nights. I'm not sure I would survive.
Location: Fort Lauderdale
Posts: 4,740
My VIN: 02613
Club(s): (DCF)
Your carb and manifold would be steaming hot after that 90-minute drive! I am not sure I could operate on anything that hot... usually, I let the engine sit overnight if I am to work on it.
Bill doesn't like me anymore... I might have to room with someone else anyway.
3.0L, automatic, carbureted