I would use the 12v wire to the warm-up regulator. I'm not sure, but I think that's the one Bill picked when we did my conversion.
Farrar
I would use the 12v wire to the warm-up regulator. I'm not sure, but I think that's the one Bill picked when we did my conversion.
Farrar
Unplug your idle ECU and see if you still have voltage at the choke. If you do then it is safe to remove your idle ECU.
With the alternator make sure you wrap the washers with some electrical tape. It will make it much easier to install them as one spacer. If you don't install it by July 9th I can install it for you at Freds. He is talking about having a tech day and going to a cruise in that night.
If you haven't swapped pulleys they can probably do that at autozone or I can do it for you with a pipe wrench and breaker bar.
CPR supply comes off the RPM relay, which will render it useless if you ever throw the damn thing away.
Look closely at my ECU compartment pic (which is #2508 BTW) and you'll see the choke wire coming off one of the old ECU harness connectors and running out the same grommet as the distributor signal wire.
Bill Robertson
#5939
I'll have to see about ditching the ECU when I'm working on the car in the coming weeks... not point in having it there if I'm not using it, and it's crowded in that compartment with the Wings-A-Loft alarm system box there as well. I can add it to the pile of K-Jet parts that I don't need any more...
Wait -- when did Ashyukun carburete? And how do you pronounce Ashyukun anyway?
Farrar
Bob Babcock. He got Jim Edwards' manifold, right before DCS'10. I am *FINALLY* putting the finishing touches on Jim's conversion, about a year late....
Bill Robertson
#5939
So, is anybody running a carb conversion manifold with a throttle body efi system like the Fast EZ-EFI or Holly Avenger on the PVR? I know they are a bit pricey at 2k on average, but they really are great turn key self tuning systems.
The idle system is NOT part of the fuel system!
I'm not sure where this comment comes from (almost looks as if it refers to a preceding post deleted by Sean), but with a carburetor the idle system (closed throttle plates) most definitely is integrated with throttle fuel delivery. The Motorcraft 2100 even uses the same metering jets for both (some carbs have different jets for idle mixture).
Bill Robertson
#5939
Okay, I admit it, I did a Robertson, reading stuff that wasn't actually written. :dunno:
I see posts referring to the ditching of the idle system as well as the fuel system when the two are wholly indepentent. The fact that you can't use the CIS is a major drawback of converting to carburetion.
Actually you *CAN*incorporate an idle air valve into a carburetor, including the 2100. Look clodely and tell me what do you see hanging off the back of this bad boy (I'll give you a hint -- it's an idle air valve): http://i.ebayimg.com/00/$(KGrHqIOKiQ...VoSYQ~~_12.JPG.
That's a 2350 BTW -- later rendition of the same carb I use.
You're trolling in my sandbox now, homeboy....
Bill Robertson
#5939
Not trolling. So why aren't you advocating the use of CIS? I do see how one could be incorporated into a carburetor, but it'd be a "wet" system and the valve would need to be able to stand up to fuel in the air it's passing.
Um, this is just a guess in the dark: because I don't want to?
Owners are free to do with their cars whatever they want. If an owner wants to install an electronically controlled carburetor, that's his or her business, and his or her business alone. Neither my opinion, nor your opinion, nor anyone else's opinion has any bearing on the decision.
Bill Robertson
#5939
Bullshit. Please read up on electronically controlled carburetors, such as the ThermoQuad and Ford VV, before posting.
Curious isn't it that Sean kicks me out of EFI threads, yet lets Martin troll away in the carburetor threads.... (Oops -- probably just got my myself temporarily banned from the new website for that one).
Bill Robertson
#5939
I'm trying to establish why the CIS can't be employed on the DeLorean running a carburetor. it'd be an improvement. I'm not trolling, I'm asking questions. You seem intent of avoiding answering. Any CIS system controls air flow bypassing the throttle. The throttle is downstream of the venturi ipso facto is would need to be a "wet" system in a carburetor. FI meters air flow pre-throttle and injects it downstream of the throttle solving this problem.
I make what I make. If you don't want it, don't buy it.
Bill Robertson
#5939
So it can't be used then?
No, I simply choose not to.
If you want to adapt a 2350 to the stock CIS ECU, knock yourself out. I've got my hands full just making what I already make.
I offer a conversion that more or less transforms a DeLorean PRV into a 1979 Mustang V6.
The reason these carb conversions work so well is because I stick to a vetted design. Now that the manifolds are welded up on a jig, positive results are virtually guaranteed on the very first key turn. Nevertheless, I test drive each conversion extensively on my own car before signing off on it.
The other advantage of sticking to a standardized design is that every conversion increases a common knowledge base.
Bill Robertson
#5939
While I'm taking an A/C break, since no one seems interested in reviving the old DMCTalk archives:
Attachment 1055 Attachment 1058 Attachment 1053 Attachment 1052 Attachment 1059 Attachment 1054 Attachment 1057 Attachment 1056
Bill Robertson
#5939
Just when I was starting to take my carburetor for granted I have noticed several threads with issues related to fuel delivery. Man I love my little Motorcraft 2100.
It is so nice to not have all the K-Jet issues. The purists can say what they want but DMCTalk is proof.
How about owners trying to get an EFI conversion to work -- talk about a barrel of monkeys.
Say whatever you want about a carb conversion -- the engine does start (and continues to run) on the very first key turn.
Have you noticed the double standard: whenever an EFI converter gets discouraged and contemplates giving up, Forum members come out of the woodwork with encouragement to keep trying. Whenever a carb converter mentions that his car started on the first key turn, Forum members tell him to shut up (or worse -- remember the carb thread on the old site, especially around Page 50...).
As long as I have a bowl full of fuel and air moving through my venturis (and only through my venturis), I have fuel delivery. It is physically impossible for my fuel/air mixture to get out of whack unless I change jets. "Reliable" and "trouble free" are totally inadequate to describe what's going on behind me.
I drive the ever living crap out of #5939 without doing anything more than change its oil (I am OCD about oil changes). I don't even wash the poor thing. I just jump in, turn the key, and go. Logged nearly 10,000 miles last year alone. Some K-Jet Boo Boo is going to jump in and say "so did I" -- I really don't give a damn. At least I can change Spark Plug #4 (in seconds, thank you very much).
I've got a few other irons in my fire at the moment, but hopefully next week I can finish Danny's and Jim's conversions. I'll definitely post pictures of Danny's -- an early model 2100 adapted to a Peugeot 604 manifold (I still have James Wallen's Peugeot manifold, so I'll be able to test drive Danny's installation). The throttle cable bracket still needs to be designed and fabbed. Most likely it will hang off the back of the carburetor itself because a Peugeot 604 manifold doesn't have any suitable mounting points (if you remember Del Silveira's installation, he mounted his throttle cable bracket to the passenger side head).
Anyone care to place bets whether or not Danny's and Jim's conversions will work on the very first key turn?
Bill Robertson
#5939
How are things working out with the green manifold? I've been wondering if you have put it on your other car yet.
#2508 is still in pieces all over my house and back yard. It will be a while before that manifold is put into service.
My hope is to have #2508 on the road in time for DMA FF'11.
I did have my machine shop fill a void in the carb adapter that will be created when I turn the manifold around (PO's were using it with the vacuum ports towards the front). I modify the passenger side port to hold my throttle cable bracket, so I need it in the back (HVAC/brake booster barb needs to be back there too). The adapter welded to that manifold is footprinted for a Motorcraft 2100 already, which is terribly convenient.
Bill Robertson
#5939
The 2100 was Ford's front line 2 barrel carburetor (for engines above 170 cubic inches) for more than a quarter century. AMC and Chrysler also used it. It remained in new vehicle production through 1991 (Jeep Grand Cherokee).
A claim was made on the old site that K-Jet is better known and supported than the 2100. That is beyond laughable. The number of Mustangs alone still running around with 2100's under their hoods has to be in the hundreds of thousands, if not close to a million (8.5 million Mustangs were built through 1985, of course not all of them 2 barrel). Don't forget F100/150's, other vintage Fords, pre-emission Jeeps, AMC V8's, etc. I recently looked under the hood of a 370 equipped 1987 school bus -- guess what I found sitting on top....
Bill Robertson
#5939
I'm still sorting out some automatic kick-down issues, but the 2100 has completely changed my outlook on my D. I want to drive the car, but was afraid that the K-jet would leave me stranded somewhere (and it did frequently). That's not a worry with the 2100. It starts and runs perfectly every time. Thanks for all your work, Bill. I'm really enjoying my car now that it's reliable. Garen Martens
The important thing to understand about putting a 2100 on a DeLorean is that the 2100 was thoroughly vetted through more than a quarter century of use. We are doing absolutely no original engineering as far as the carburetor itself is concerned (remember that Ford used the 2100 as original equipment on its 2.8 liter V6's). An owner can simply bolt one on (suitably sized and jetted of course) and expect known operational characteristics, engine health itself permitting. I'm not saying carburetion in general is good or bad -- only that a 2100 in particular will produce predictable results.
Re: full throttle kickdown: first & foremost ensure your microswitch is working via a continuity check. It's a cheap switch that does go bad. The plunger on the switch I use for test fitting tends to get stuck inside and not spring back out.
If the switch is OK, make sure your throttle arm is closing it at full throttle. Holes in the bracket are oblong so you can adjust it front to back.
The switch closes a ground -- make sure the black wire from it has continuity to the block.
Bill Robertson
#5939
Just because a 2100 is basically guaranteed to always work properly (no vaccum leaks elsewhere), do *NOT* assume that fuel delivery itself is assured. There are two trouble spots elsewhere in the system that can, and often do, fail:
1) If you are using factory pump wiring, you are every bit as dependent upon the RPM relay and inertia switch as a K-Jetter. RPM relays are notorious for failure, especially after prolonged use. I've also seen several melted inertia switches, including my own. Any failure in the pump electrical circuit will allow the bowl to run dry and the engine will stop.
2) Airtex has had QC issues. I lost a pump to bearing failure at DMA FFT'09 (the poor thing jumped around like a Mexican jumping bean, but moved almost no fuel). Users of my fuel pump carrier are not beholden to Airtex pumps -- any pump that fits inside can be substituted, or a length of hose can be run from it to a pump mounted elsewhere.
It is possible to limp a carbureted DeLorean to a safe haven in case of pump failure by filling the bowl manually. I carry a tiny funnel and an empty Coke bottle for such purpose, and as stated at DMA FFT'09 I had to do just that. In a worst case scenario you can dip fuel directly out of the tank. Each bowl full will get you 1/2-3/4 miles, terrain and speed depending. Fill the bowl through one of the vent chimneys. Be careful not to overfill it or you will flood the intake and lose precious distance rev'ing the engine to clear out excess fuel.
The longest distance I have ever limped a car is approximately 10 miles. In that instance I was able to rig up a Coke bottle to gravity feed the carb so refills were nearly a mile apart (I could only run the Coke bottle halfway down before fuel level dropped below the neck):
Attachment 1313
This was a high compression 460, which only gets 8-10 MPG in the best of circumstances. A similar arrangement on a DeLorean might yield up to 2 miles between refills.
Bill Robertson
#5939
Sorry, didn't see this until I went back hunting to see what I could safely ditch from my ECU compartment while I'm working in there (need to hunt down the picture of Bill's compartment, though a keep/remove list wouldn't hurt :P).
16655 has actually never run in my possession with anything other than the carb, and I've never regretted it at all. I'm firmly convinced there's no way it would have made it to DCS last year on time if I'd been trying to get the K-Jet running for as long as the car had sat and how much of a disaster the fuel tank was.
It's technically pronounced Ash-you-coon. Back something in the vicinity of 15 years ago or more when I was in college first had to start coming up with a username for sites as the internet became more prominent, my nickname (as there were several 'Bob's) was Ash (due to my love of Army of Darkness). However, due to the popularity of ANOTHER 'Ash' from Pokemon, there wasn't anyplace that 'Ash' was available as a username. As most of the sites I was at the time signing up on were in one way or another related to anime (Japanese animation), I used what I knew of the language to 'romanize' the name- any words that end in a consonant besides 'N' usually get a 'u' added to the end (the 'yu' makes it a bit more pronouncable... yeah, doesn't matter in application, but made sense at the time...) , and '-kun' is a common-usage honorific. I've just stuck with using it ever since as it's not something I've ever seen anyone else use...
CIS has nothing to do with ignition. They are two totally separate systems.
I am currently running with a Ford Duraspark module temporarily substituted for the Bosch ignition ECU (testing for another owner):
Attachment 2319
It's just laying loose in the ECU compartment.
Bill Robertson
#5939
Owner is in Georgia.
We don't for certain whether his Bosch unit is bad -- I just wanted to be ready in case it is (you can't buy a replacement Bosch ECU over the counter).
I do intend to make another adapter to keep in my car, for my own future contingencies. Duraspark modules are stock items at all parts houses nationwide.
To be brutally honest, I haven't noticed any difference running a Ford module versus Bosch. There's a loose wire from the Duraspark ECU that is normally attached to a starter trigger signal (not present in the Bosch harness), but my car is starting just fine without it.
Bill Robertson
#5939
The delicious tangent can be continued here:
http://dmctalk.org/showthread.php?70...arbs-thread***
Pfft -- shows you how long it's been since I watched any anime. :lol: OK, back on topic...
Bill, I'm gearing up to replicate your ground bus. Can you please explain why you used plates to connect some of the wires instead of grounding them directly to the brackets in the compartments behind the seats -- was it because the bolts were different sizes? Thanks!
Farrar
Brackets in the ECU and relay compartments are as crappy as the rest of the car (my opinion). That ground block is 1/8" thick stainless steel. The crappy (my opinion) ECU bracket merely has to hold it still, which debatably is within its realm of capability.
I have no idea what I may need to ground in the future. That's the purpose of the 1/4" center stud -- to give me a convenient, non-crappy ground point for anything I ever need to attach.
I also am using the stainless bar across the front of the car as a ground block (both ground junctions behind the headlights are tied into it with 8 gauge wire). It is attached to the radiator bracket bolt with 8 gauge wire -- that's the only part of my bus that isn't 4 gauge (ground bus originates at that bolt).
Bill Robertson
#5939