Where did Ron say anything about injector? He just needs a place where air gets in.
Sorry but I've got no experience with nitro boosting so thats all Greek to me. I don't understand how an EFI system would suddenly be able to adapt to a hose with fuel in it. Would something need to be reprogrammed? I'm not trying to be smart, just asking a serious question.
No, I don't carry a coke bottle full of gas around with me. There is a coke bottle in my car that is half full of coke though. Hopefully after this weekend I will have about 20 bottles full of diet cheerwine as well. If I truely got in a pinch, I would be able to rig something up with a bottle, fuel line, and gas from the tank.
As I have said many times before, I choose to carry a spare fuel pump. I suspect my fuel pump problems to be ground related so last night I wired a ground connection directly from my battery to the fuel pump. I'm suprised no one has critisized this yet since I no longer have an inertia switch or RPM relay hookekd up anymore.
Lets wait and see if I have any fuel pump failures after 20+ hours of driving this weekend. If my fuel pump fails with with a solid ground connection, then we have a problem.
Originally I was going to be lazy and keep driving as is, without a straight ground connection, but I figure this weekend is an excelent chance to test my theory.
What I was getting at with the ether is that all you need is a vacuum source to the intake (plenum) to run the engine. Sure, you are a lot better off with a carb (A/f control) if the pump goes out but you will only get a 1/4 mile or so out of it... I've never been that lucky when I run out and it's not very safe especially since it will run lean and be VERY prone to backfire when it runs out....not practical at all except in a very few instances at best. I can't imagine rigging up anything in a D with the tank lower than the engine...except like I said a lot of BS for a 1/4 mile trip.
I think I know what a lot of the problem is with carb pumps going out...we can check it out at the meet (I posted it some where before but no response).
The best thing anyone can do to make their car as reliable as possile is to understand it.
Easy to say!
I thought I'd post this link to a friend of mine in the Alpine club whose thread I read today. he's sunk umpteen thousands into restoring and modifying a GTA. It ain't just DeLorean owners who think their cars are cursed...
http://www.renaultalpineownersclub.c...pic.php?t=5380
(and I'd like to point out that Simon's avatar is the source of a long running joke)
Oh, and the starter and alternator circuits are identical to the DeLorean's.
I'm thinking (other than trash, electrical) you might be using the wrong pumps or pluming depending on the carb(s)...cycling running wide open or labored, or, mostly pumping through the internal by-pass valve...The ones I see posted around here might be being over worked since they aren't pressure regulated and run ~2 times the pressure required by the float's needle valve, most of the time. They never rest (they are not made to take it like todays internal pumps...diferent "style"). In the old days, we used to use AC adjustable pressure regulated rail mounted pumps or one matched to (slightly above) the float requirements on racers to pitch mechanical pumps and get rid of the drag... The floats needle valve's on-off pressure is not that tight which allows for even more rest time...
Just a guess and food for thought...I'll see if I can dig up the post if you want or we can talk about it Saturday.
I was sort of thinking the pump I have might be too high of a psi pump, but Bill has installed pumps with these specs on many other cars without any problems. I'm not going to rule anything out, but like I said, it could just be a ground issue. We may or may not know the answer to this by the end of Saturday. If my pump fails then perhaps I need to look into a lower PSI pump. If my pump doesnt fail, then perhaps the direct ground connection resolved it. If it is ground related I will correctly fix it by eventually replacing the inertia switch and installing a full car ground bus.
Do you know if they are locking down or ??? Ever open one up afterwords?
Bill using the same plumming, carb (I guess I know that answer;-)
This is where I don't say it would be easier to work out k-jet :devil:
Maybe if you would leave the accumulator in when you go carb, it would ease the peak pressures in the pump. I never knew why Bill insisted on running a new line.
I actually thought about installing a fuel pump meant for EFI (30 to 45 PSI) and then using an inline fuel pressure regulator to dial the pressure down to 6 PSI. You could probably use the stock fuel lines for this -- swap the regulator for the accumulator, perhaps? -- unless the regulator has a return line, in which case you'd have to mount it elsewhere. Some regulators have a return and some don't; I am not sure what might be required, but there's more than one way to skin a cat.
For what it's worth, I think running a fresh ground from the inertia switch would extend the lifespan of DeLorean fuel pumps.
Farrar
On a side note, I thought this looked too cool to pass up at a Ford swap-meet. Technically, it's fairly accurate. Only 4 cubes off the actual displacement.
http://i135.photobucket.com/albums/q...3/923acc75.jpg
Do any of you guys that have added air filters directly on top (like the picture above) of any engine type (K-Jet, Carb, EFI) believe that the incoming air is therefore much warmer than if piped in from the pontoon? Given the meager air flow through the engine compartment and the exhaust pipes, cats and muffler all radiating heat straight up to the engine cover and sucked into the air cleaner, I would think there would be a noticeable difference.
Many D owners go so far as to remove the so called stove pipe pre heaters for this very reason.
This can be moved to a new thread by admin if someone should believe it to be inappropriate in the carb thread. It is my observation however that many of the carb conversions seem to have their filters right on top, hence these guys are a good bunch to ask the question to.
I seem to recall Bill's answer to that was "It was good enough for the Pantera..."
I have thought about trying to add a fresh air duct to the air cleaner housing, but it would involve too much fabrication for my taste. Perhaps someone else will go this route and see if it adds any "performance."
Farrar
A Dual-Snorkel fabrication like this one could work.
http://compare.ebay.com/like/3601552...=sbar&_lwgsi=y
Then if you could find any of those Legend Turbo Delorean side-scoops to feed it, it might keep things cooler.
Absolutely I can claim the same.
I honestly look at Carb conversions as just another form of customization. What the only thing that I ever took exception to was a couple of people people who rather than simply saying something like, "I just want to switch to a Carb because it's something I prefer.", they felt the need to justify the choice by putting down stock fuel injection and ultimately the car itself as well as other people. The thing is that you don't have to justify the switch at all. If you want to do it, and it especially helps you to keep the car on the road, and more importantly helps your enjoyment of your car, by all means go ahead. It was the context of the conversation before that led things in the wrong path. Here is the formula:
- Negative Claim made against K-Jetroinc.
- Rebuttal to claim offered.
- WHY ARE YOU TRYING TO PERSECUTE ME!
- Repeat. Cycle 2 switches claims to vehicle reliability. Cycle 3 adds personal attacks.
Like I say, to me a Carb is just a customization option. But attacks against the car are what really sparked the anger and escalated everything. It would have been like someone saying that they were doing a BTTF conversion simply because they didn't like the look of the DeLorean.
In any case though I'm just glad that this has all been put in the past so that people including myself can move on...
Admittedly I'm not gonna be nearly as much help as others with carbs having only ever really owned 1 car with a carb, and I sold it before wrenching on it. However, I do actually believe that I might be able to throw a little light onto the subject of the issue with Fuel Pumps. I think that I know what's going on, but it's gonna take a couple of stories here.
First story: Back in 2000 I was driving my car, and it just died for no reason at all. I couldn't figure it out (this was the day that my car almost got me killed trying to move it out of traffic). I got home and started checking for continuity. I was getting a solid 12V from the Feed jumping the RPM Relay and using an independent ground, but not when it Used the Ground wire. I don't remember the numbers, but it was pretty low and sporadic. So I was going to check continuity from the Inertia Switch's ground.
Now before going on, it's important to understand EVERYTHING that the Inertia Switch does, as well as what circuits it's integrated into as well as HOW it is integrated into them.
The first thing to know is that the Intertia Switch doesn't kill power to the Fuel Pump. It kills GROUND (or Earth as all the stickers on my car say). The 12V feed comes directly from the RPM Relay.
Second the Inertia Switch is not a SPST switch. It's a SPDT Switch where I believe the Single Pull inside of the Inertia Switch is the Ground. In position 1 with the Plunger down, the Switch connects to the Fuel Pump's Negative terminal in order to allow the pump to run. In Position 2 it connects to the Brown/Pink wire on the Unlock feed for the Door Switches and Warning Light on the A/C Panel. This is the Unlock Trigger Wire that senses (or in this case tricks) the Door Lock module into thinking that one of the doors has been unlocked and causes the other Door Lock Solenoid to pull open. Or in this case both.
Now for allot of you that didn't know this, you're probably wondering WTF?!? right about now. But the idea behind this was in case you ever got into an accident where the Inertia Switch was triggered, you doors would be unlocked for a rescue worker to easily gain entrance into the car to rescue you.
And now, back to my story:
When I went down to the Inertia Switch to check for Continuity on the Ground Circuit in Between, I discovered that the gray plug for the Inertia Switch was melted. Being tired, lazy, and already having the Inertia Switch trip on me once when I hit a pot hole I simply just unplugged it, and then cut the wiring harness for the fuel pump and ran a dedicated ground wire to the grounding point on the Radiator Bracket. Since that time it's ran strong and with the exception of a bad Charcoal Canister, I never had another problem again with the fuel pump.
Second Story: Back in 2004 I had my headlight switch start acting funny and working intermittently. I pulled it out one night after it refused to turn ANY of my lights on, and discovered that it had melted! I shoved a spare jumper wire that I had in to get the clearance lights on, and drove home with my high beams. Got home, found that the jumper wire was hot as hell! Checked all of my light bulbs, and discovered that my Left Front clearance lens had water stains inside, and had a cracked gasket. Pulled the lens off the fender and found that the bayonet socket was rusted beyond any repair. I ended up having to cut it out and then splice a new socket in as well as bought a new gasket. After that the jumper wire ran cool until I was able to put my spare switch in.
Now, what does any of this have to do with Fuel Pumps? Everything. See the rust in that light socket wasn't bad enough to cause a dead short, but it was enough to place extra draw onto the circuit. Not quite enough amperage at once to blow the fuse, but just enough to heat the wires significantly and damage the weakest link in the circuit.
I'd wager money that the problems with the Fuel Pumps are related to the Inertia Switch and corrosion inside. So far it's been the ONE place we can't get to, and I think this here is what's happening: Rust and corrosion forms and acts like a resistor that starts sucking amps. This places and extra load onto the circuit. And that load comes directly through the fuel pump. And seeing how fuel pumps are so susceptible to heat damage, I'd bet this is what's causing them. The K-Jet especially and EFI pumps probably have beefier components inside since they have to deal with higher pressures than Carb pumps. Not to mention that carb pumps probably also aren't usually installed with scenarios such as these where Inertia Switches are involved, let alone gas tanks next to heat sources.
On a side note I noticed that on Hervey's website he has a special note to check and make sure that the Plug for the Inertia Switch isn't melted. Hmmm...
I'd recommend checking resistance between the contacts on the Inertia Switch and see what you come up with. Likewise the next time someone complains about a noisy fuel pump and it's not an issue of the fuel lines touching the firewall or a seized diaphragm on the Carbon Canister, let's have them pull their Inertia Switch and check that plug for heat damage.
So far the fuel pump is holding up with the new ground wire. So far I've driven at least 450 miles today without a single problem.
Right now I'm at a nice Walmart somewhere outside of Montgomery, AL. I'm about to turn the parking lot into a camp ground and the Delorean into a camper.
Pleasant dreams!
I am proud to say I drove a total of 1278 miles since Friday. My car made it to Sean's house, and then Ron's (way up in the mountains with a tuna fish can baffle) and all the way back down to my house without a single fuel delivery problem at all.
Shoot, I didn't have any problems on this trip except for some thug in Biloxi that wanted to buy my car at a gas station. He claimed to have $10k cash money on him and he wanted to buy the car on the spot.
I now declare my fuel pump issue to be resolved. The new ground seems to have taken care of the problem I had before.
I also have an idle problem... as well as an acceleration problem and a cold start problem... but I digress. My car will idle high when first started then go back to normal. Then, even after warm, it'll idle at about 2,000RPM until I punch the gas quickly. I'm guessing this has something to do with the choke. Also, at times, after awhile of driving, the car will idle very low 450-500RPM it will also stall at times in during this "mode" of operation. I'm also going to start keeping better track of my mileage because I think mine has dropped drasticly.
Also the car bogs down upon acceleration VERY heavily when you first start the car. Even during normal operation I cannot floor the accelerator without heavy "bucking" This carb conversion only has about 300miles since installation. I also changed the plugs shortly after the conversion.
This is normal. The fast idle circuit is designed to idle the car high until your choke is completely open. This is to keep a cold engine from stalling.
It sounds like yours is set a little high. Turn the fast idle screw after starting the engine and keep in mind the engine needs to be cold when making these adjustments. I also like to hold the choke plate closed while I turn the fast idle screw. You may need to lightly tap the accelerator to engage the fast idle screw before making your adjustments as well.
Once the car is warmed up the fast idle circuit no longer operates. The car switches over to the idle jets. You will need to adjust your idle jet screws while the engine is hot to get it to idle where you would like.
Not quite sure what is going on there. How wide/small is your plug gap and are you using new plug wires, cap, rotor, and coil or are you using 30 year old stuff?
Have you talked to Bill about any of this?
Although a bit high (depending on ambient temperature) it is normal for most carb engines to gain RPMs as it warms and require you to pat the peddle to get the linkage to drop off of the high idle cam/step...
All of your symptoms could be the carb.
Easiest first:
Cold start and/or bogg before acceleration and/or 'bucking' - classic symptoms of the spray pump failure/adjustment.
Bogg and/or buck low- starve then surge of fuel (float adjustment, carb filter, fuel filter, pump strainer, pump...), timing
Cold start and/or high idle (especially if accompanied with smoke and/or rich smell) - choke setting (opens late) may set high idle cam, sticky linkage.
High/low idle- sticky linkage.
Air/fuel adjustments (depending on carb type) can screw everything up.
Most adjustments/settings are required to be done in a specific order.
I would let it sit all night (KEY), then make certain all linkage is free. Be sure to check with throttle AND choke in all positions and combinations! Next check spray pump sprays throughout its full stroke. Check choke settings (again, it MUST sit all night..but recheck with throttle ~1/2 open after warm up also).
Then go from there...If nothing found, go back to basics (timing, vacuum leaks, fuel quality, internal carb problem (save yourself some trouble and borrow one to test with if possible.))
EDIT: RE your correction WRT choke in morning... Befor you start you should hit the pedal once to let the choke reset after cooling. It will set the fast idle then, if required. If you don't, it stays where you left it when you last touched the pedal...
I really wish someone would've made a video on how to set these thing up.
The following procedure, adapted from another website, assumes that you have set the carb to "basic" settings of: idle air mixture screws out 2 turns, curb idle screw in 1.5 turns. This basic setting should allow the engine to start and idle, so that you can make the adjustments (on a fully warmed engine).
The first thing to do is not set the idle speed, but instead to set the idle mixture screws to lean best idle setting. First, turn in the mixture screws until the engine dies or runs worse. Then back out the screws ¼ to ½ turn at a time -- the engine should pick up speed and begin to smooth out. Back out ½ turn more, or until the screws do nothing or the engine runs worse, then turn back to the point where it ran its best.
Now that the mixture screws are at their best running location, you can adjust the idle speed screw. The screw will be sensitive and it should only take ¼ to ½ turns to achieve the idle speed you like.
Check and set idle to your driving preference. Put the car in gear and apply slight load, (AC on) and set the Idle as you like it. Don’t set it too high, as this will cause causes excessive clutch and brake wear.
Recheck timing and vacuum hook ups. Recheck mixture screw to lean best idle again. If all is still best and smoothest idle then confirm and note the final settings.
If you need a video, perhaps I can make one.
Farrar
Farrar, these notes are very helpful. A video of you applying the steps would be awesome! All of the carb-guys could use it as a reference. Not to mention the gift of my eternal grattitude.